Summary of Contents for INHECO Heated Lid
- Page 1 INHECO Heated Lid Heated Lid Part No.: 8900033 ► User´s Manual Doc ID: 900678-001 July 2020...
- Page 2 This manual and the information herein have been assembled with due diligence. INHECO GmbH does not assume liability for any misprints or cases of damage resulting from misprints in this manual. If there are any uncertainties, please feel free to contact sales@inheco.com.
-
Page 3: Table Of Contents
PRODUCT DESCRIPTION ............... 06 Intended Use ....................06 Scope of Delivery ..................07 Functional Elements ..................07 Labels ......................08 Technical Data Heated Lid ................09 SAFETY INSTRUCTIONS ................ 10 Product-specific Risks ................. 10 Technical Alterations ................... 11 Malfunctions ....................11 HARDWARE INSTALLATION.............. -
Page 4: Important Notes
INHECO GmbH. This manual is part of the Heated Lid and must be retained until the device is disposed and must be passed on with the Heated Lid when the device is taken over on to a new user. The Heated Lid meets the acknowledged rules of technology and comply with today‘s standards. -
Page 5: Explanation Of Abbreviations
Broken seals on INHECO lead to the loss of warranty as well. INHECO will only accept parts / devices for return that do not pose a threat to the health of our staff. In particular, the devices may not have been used in Biosafety Level 3 and 4 environments, or have been exposed to radioactive or radiation materials. -
Page 6: Product Description
CE and UL certification. It is mainly used on robotic platforms and systems in LabAutomation. The Heated Lid is designed specifically for use in Life Science and In Vitro Diagnostics. It is prepared for easy integration into IVD applications, but the final IVD validation has to be performed by the first marketer (IVD application). -
Page 7: Scope Of Delivery
In case of parcel or product damages, make photos of the damaged boxes and products and email them to techhotline@inheco.com immediately. Transportation damages must be reported to INHECO within 7 days of delivery. The following components should be included in each shipment: Fig.1:... -
Page 8: Labels
The electrical specification on the label must meet your local situation. The label is placed on the top of the Heated Lid. The identification label must not be removed. If it has become illegible or falls off, it has to be replaced by a new identification label. -
Page 9: Technical Data Heated Lid
2.5. Technical Data Heated Lid Technical Data incl. Dimensions Input voltage / max. current 24Vdc / 4.8 A Temperature range ambient to + 115°C [ambient to +239°F] Temperature range ambient 15°C to +32°C [+59°F to 89.6°F] Sensor type two PT100... -
Page 10: Safety Instructions
- The device must not be used if the device itself or the power cable shows visible signs of damage. - You can suffer an electric shock and injuries, if Heated Lid is not connected properly or if you do not disconnect the device from the TEC Control Unit (STC / MTC) outlet before opening the housing. -
Page 11: Technical Alterations
Technical Alterations - Do not alter the product. Any modification or change which is not approved by INHECO leads to the loss of warranty. Broken seals on INHECO devices lead to the loss of warranty as well. - Use only original parts provided by INHECO. Parts provided by other suppliers can impair the functionality of the device. -
Page 12: Hardware Installation
• Disconnect the power cord of the TEC Control Unit. • Connect the heating/cooling/shaking device to the appropriate Slot Module and lock the connector. The Heated Lid must be connected to a Black Slot Module. • Connect the power cord of the TEC Control Unit. -
Page 13: Labware Use
4.3. Labware Use The Heated Lid fits to all plates, tubes, racks etc. used on INHECOs heating/cooling & shaking units. NOTE As the temperature can be selected up to +115°C [+239°F] check whether your labware is suited for the selected temperature. If the temperature is too high for the material of your labware, the labware might get squashy or even melt. -
Page 14: Maintenance
- INHECO product number of the device (shown on device label) - INHECO product name of the device (shown on device label) - INHECO serial number of the device (shown on device label or via software) - Detailed error description - Error code report (generated with software “MTC/STC Demo Tool”) -
Page 15: Cleaning
Do not use aggressive cleaning fluids such as acetone, or abrasive cleaners. The plastic frame of the Heated Lid can be cleaned with a cloth dipped in water or methanol. No part of the body should be immersed in the solvents. Do not use aggressive cleaning fluids such as acetone or abrasive cleaners. -
Page 16: Decontamination
7.4. Decontamination Decontamination is required before return of a device to INHECO in case it has been exposed to human or animal blood/fluid/tissue or has been exposed to biological, or chemical materials. The surface decontamination should include a wipe-down of the housing surface with a decontaminating solution. -
Page 17: Accessories
ACCESSORIES 8.1. Multi TEC Control (MTC) / Single TEC Control (STC) Product Name Description Part Number Multi TEC Control controls up to 6 INHECO devices individually 8900030 Single TEC Control controls 1 INHECO device 8900031 8.2. Slot Modules Product Name... -
Page 18: Appendix
Multi TEC Control (MTC), Multi TEC Control Compact (MTCC) (with Slots 2400125+2400128+2400211+2400205) connected with corresponding devices: CPAC Microplate, CPAC Ultraflat, Thermoshake or Teleshake, HeatPAC, Heated Lid Part No: 8900029, 8900030, 8900031, 8900036, 8900033 7000163, 7000168, 7000179, 7000190, 7000166, 7100136, 7100146, 7100144, 7100160,...
Need help?
Do you have a question about the Heated Lid and is the answer not in the manual?
Questions and answers