Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Jefferson Professional Tools & Equipment JEFPDB0750-16S
- Page 1 Bench Drill 230V ~ 50Hz JEFPDB0750-16S User Manual v.1.2...
-
Page 2: Table Of Contents
USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz Contents: About This Document: Introduction Specifications Safety Information Parts Identification Unpacking & Working Environment Assembly Instructions Settings & Adjustments Using Straight Shank Drill Bits Using Morse Taper Drill Bits... -
Page 3: Specifications
USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz Specifications: Max Drilling Diameter 16mm (5/8”) Motor Power 750W Chuck Capacity 3-16mm Input Voltage - Frequency 230V-50Hz Spindle Travel 85mm Number of Speeds Speed 50Hz 180-2770R.P.M. Spindle Taper Max. - Page 4 USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz Safety Information: (continued) Equipment Safety • Always keep guards in place and in clean, working order. A guard or other part that is damaged should be properly repaired or replaced using Jefferson approved parts.
-
Page 5: Parts Identification
USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz Parts Identification Pully Cover Motor Switch Chuck Guard Chuck Feed Handle Table Table Holder Belt Tension Lock Knob Column Support Base Main Housing Column Bolts Depth Stop Lock Knob Unpacking &... -
Page 6: Assembly Instructions
USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz Assembly Instructions Base & Column Fig.1 Fig.2 1. Carefully remove contents from the packing box. 2. Select a firm, level surface on which to assemble the bench drill. -
Page 7: Settings & Adjustments
USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz Settings & Adjustments Fig.22 Fig.23 Table Height Adjustment 1. Loosen the table support lock (Fig. 22). 2. Rotate the table adjustment handle to set the desired table height and tighten the table rock to secure the table in position (Fig. -
Page 8: Pre-Setting The Drilling Depth Bench Type
USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz Pre-Setting The Drilling Depth Fig.32.1 Fig.32.2 To set the depth of the hole, adjust the depth stop as follows: • Loosen depth stop lock knob by turning in an anti-clockwise direction see (Fig.32.1) -
Page 9: Drilling
USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz Drilling 1. Ensure the bench drill is switched off and disconnected from the power supply. 2. Loosen the jaws of the chuck with the chuck key by turning in an anti-clockwise direction and insert the selected drill bit into the as far as it will go. -
Page 10: Troubleshooting
USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz Troubleshooting PROBLEM POSSIBLE CAUSE SOLUTION Noisy operation a. Incorrect belt tension a. Adjust tension (under load) b. Dry spindle b. Remove spindle and quill assembly and lubricate c. -
Page 11: Circuit Diagram
USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz Circuit Diagram GROUND CABLE YELLOW AND GREEN MOTOR CABLE MOTOR DA7B NVR SWITCH www.jeffersontools.com... -
Page 12: Parts Lists & Diagram
USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz Parts List & Diagram www.jeffersontools.com... - Page 13 USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz NUMBER DESCRIPTION SPECIFICATION QUANTITY Base Column Flange Spring Washer Outside Hex. Bolt M10×25 Rack Column Hex. Soc Set Screw M6×10 Collar Rack Cross Recess Countersunk Hd Screw M6×16...
- Page 14 USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz NUMBER DESCRIPTION SPECIFICATION QUANTITY Speed Label Pulley Cover Micro Switch Flat Washer Spring Washer Spring Washer Flat Washer Micro Switch Pressing Claw Eccentric Shaft Middle Pulley Bearing...
- Page 15 USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz NUMBER DESCRIPTION SPECIFICATION QUANTITY Spindle Socket Main Spindle Bearing 6006 Washer Ø47 Taper Spindle Chuck Working Table 290×290 Table Arm Outside Hex Bolt M16×30 Spring Washer Locking Handle M10×32...
-
Page 16: Environmental Protection
USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz Environmental Protection Recycle any packaging and unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. -
Page 17: Ec Declaration Of Conformity
RoHS Directive Equipment Category: Bench Drill / Pillar Drill / Drill Press EU Member State United Kingdom Product Name/Model: JEFPDB0750-16S - 750W Bench Drill - 16 Speed Signed by: Stephen McIntyre Position in the company: Operations Director Date: 19 August 2019... -
Page 18: Limited Warranty Statement
USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz Limited Warranty Statement Jefferson Professional Tools & Equipment, or hereafter "Jefferson" warrants its customers that its products will be free of defects in workmanship or material. Jefferson shall, upon suitable notification, correct any defects, by repair or replacement, of any parts or components of this product that are determined by Jefferson to be faulty or defective. - Page 19 USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz Claiming Warranty Coverage The end user must contact Jefferson Professional Tools & Equipment (Tel: +44 (0) 1244 646 048) or their nearest authorised Jefferson dealer where final determination of the warranty coverage can be ascertained.
- Page 20 USER MANUAL v1.2 JEFPDB0750-16S 750W Bench Drill • 16 Speed • 230V ~50Hz IMPORTANT! SAFETY FIRST! Before attempting to use this product please read all the safety precautions and operating instructions outlined in this manual to reduce the risk of fire, electric shock or personal injury.