Subscribe to Our Youtube Channel
Summary of Contents for SISTEM AIR AUTO Jet TURBIX
- Page 1 ByTecnoplus s.r.l. CENTRAL VACUUM SYSTEMS w w w . s i s t e m a i r . c o m MANUALE TECNICO Technical manual Manuel technique Technisches Handbuch Manual técnico V 1.0.0...
- Page 3 ByTecnoplus s.r.l. CENTRAL VACUUM SYSTEMS INSTRUCTION MANUAL • Type: separators with automatic unloading Line • Model: AUTO Jet • Revision 1.0.0 INDEX USING THE MANUAL TECHNICAL FEATURES CONSTRUCTION FEATURES SAFETY FEATURES 4.1 Safety symbols 4.2 Declaration of the absence of harmful substances 4.3 Safety measures regarding fi xed guards 4.4 Safety measures regarding movable guards INTENDED USE OF THE MACHINE...
- Page 4 To obtain the best results, the use of original SISTEM AIR consumables is recommended The SISTEM AIR trademark mentioned in this manual is a registered trademark and belongs to to the owner TECNOPLUS S.r.l.
-
Page 5: Technical Features
2- TECHNICAL FEATURES Separators with automatic unloading Auto Jet Template TURBIX Article 7010.3 Control panel Degree of protection Supply V ac Absorption Container capacity Pneumatic actuator pressure Dust entry Blowing motor exhaust outlet Pressurized air inlet 3/4” Nozzle pressure 6 ÷10 Maximum number of recommended operators Weight Size A... -
Page 6: Construction Features
Auto Jet Instruction Manual ByTecnoplus s.r.l. CENTRAL VACUUM SYSTEMS 3 - CONSTRUCTION FEATURES Suction module connection Dust entrance connection Stainless steel cyclone cone Electric control panel Pressure regulator pneumatic actuator Compressed air nozzles Nozzle solenoid Load bearing frame valve Stainless steel cylinder dust collection Exhaust pipe Ø... - Page 7 In particular, the special Auto Jet Turbix separator is a unique product of its kind: the presence of the cone with cyclonic effect allows it to have an extraordinary ability to eliminate dust, preventing it from clogging the central vacuum unit fi...
-
Page 8: Safety Features
Auto Jet Instruction Manual ByTecnoplus s.r.l. CENTRAL VACUUM SYSTEMS Finally, through the three potentiometers on the control panel it is possible to adjust the following operating parameters: - suction timing (to avoid excessive fi lling of container) - aperture opening timing (to be set according to the specifi c weight and consistency of the vacuumed material) - compressed air jet timing which operate in emptying phase Using the TEST button it is possible to test these three settings immediately, in order to fi... - Page 9 4.1 Safety symbols DANGER OF ELECTRICITY OR ELECTRICAL CURRENT Danger of serious personal injury. During maintenance operations, disconnect the power supply and ensure that the power supply cannot be restored. DANGER OF CUTTING Danger of serious personal injury. During maintenance operations, disconnect the power supply and ensure that the power supply cannot be restored.
-
Page 10: Intended Use Of The Machine
When using the system to vacuum liquids, it is advisable to consult Sistem Air, in order to make the right adjustments so as not to compromise the functionality of the motor unit. - Page 11 7 - KIT AND ACCESSORIES The sales package of the plant also includes the accessories kit, comprised of the following elements: N°1 AUTO Jet N°2 rubber sleeves for connection to the suction tube network N°4 metal clamps for fi xing the sleeves N°1 installation, use and maintenance manual 19/04/2018 Rev:2.0.0...
-
Page 12: Installation
fl ooding, or high temperatures. The AUTO Jet Turbix separator can be installed in service rooms or in service areas protected from bad weather, humidity and excessive temperature changes (working room temperature “-5 ÷ 45 ° C”, relative humidity 20 ÷... - Page 13 8.3 Reversibility The AUTO Jet is designed to be able to position the dust inlet fi tting according to installation needs. Unscrewing the 2 upper screws, fi xing to the frame plate, and the 8 lower screws, fi xing to the cylinder, it is possible to rotate the inlet of the sucked material with pre-defi...
- Page 14 fi lter cartridge Suction motor unit The sizing of the suction unit and of the suction lines leading to the Auto Jet Turbix must be made giving consideration to the number of simultaneous users and the type of material to be vacuumed.
- Page 15 8.5 Connection of the compressed air network Regulator fi lter pneumatic actuator Compressed air connection G 3/4 “ - CAUTION - NEVER APPLY PRESSURE OVER 10 BAR OR LOWER THAN 6 BAR Connection of compressed air system: Connect the compressed air system to the G 3/4 “fi tting located on the back of the AUTO Jet system. It is always advisable to apply the maximum available pressure to the system, always respecting the limits indicated, so as to be able to have the greatest fl...
-
Page 16: Electrical Connection
Auto Jet Instruction Manual ByTecnoplus s.r.l. CENTRAL VACUUM SYSTEMS 8.6 Electrical connection Electrical control panel Open the front cover of the control panel to gain access to the terminal block for the electrical connec- tions. The complete schematic diagram is present inside the control panel. 19/04/2018 Rev:2.0.0... -
Page 17: Application Examples
8.7 Application examples Solid residues / powders The self-supporting frame can be raised or fi xed to other structures to allow the positioning of the separator on top of trolleys, Big Bags or other col- lection systems. In this way the handling and any recovery of the vacuumed materials is facilitated. -
Page 18: Control Panel
Auto Jet Instruction Manual ByTecnoplus s.r.l. CENTRAL VACUUM SYSTEMS 9 - CONTROL PANEL Nozzle test button and Vacuum line sockets pneumatic actuator isolator Network presence warning light potentiometer TEST Main Switch GREEN Potentiometer BLUE potentiometer Main switch: magnetotherrmic switch for isolatiing and protecting the power supply line of the control panel. -
Page 19: Commissioning And Use
10 COMMISSIONING AND USE Before putting the AUTO Jet system into service, make sure that the tubing system is correctly and securely fi xed to it, that the electrical and compressed air connections have been made according to the law, as well as the systems to which it is connected, and that the pressure in the circuit complies with the limits indicated in chapter 8.5 Set up a vacuum cycle to check its operation, then before vacuuming the selected material, check that there are no foreign bodies inside. -
Page 20: Warranty
Auto Jet Instruction Manual ByTecnoplus s.r.l. CENTRAL VACUUM SYSTEMS 12 WARRANTY PRODUCT LIMITED WARRANTY CONDITIONS The Manufacturer guarantees to the original purchaser the absence of defects in material and workmanship of the product for the period stated, from the date of purchase. Except as prohibited by applicable law, this warranty is non transferable and it is limited to the original purchaser. -
Page 21: Declaration Of Conformity
TIPO Complementi per aspirazione MODELLO Separatore AUTO Jet Turbix ARTICOLO 7010.3 è conforme e rispondente alle disposizioni delle seguenti: Direttive CEE pertinenti: - 2006/42/EC... - Page 22 Auto Jet Instruction Manual ByTecnoplus s.r.l. CENTRAL VACUUM SYSTEMS 19/04/2018 Rev:2.0.0...
- Page 24 F0920548 27020 Gravellona Lomellina (PV) ITALIA - Via Cilavegna, 53 - GPS: N: 45° 19’ 28” ; E: 8° 45’ 32” Tel. + 39 0381 650082 - Fax +39 0381 650120 - info@sistemair.com...
Need help?
Do you have a question about the AUTO Jet TURBIX and is the answer not in the manual?
Questions and answers