Download Print this page
Panasonic BEP-NRH005 Series Instruction Manual
Panasonic BEP-NRH005 Series Instruction Manual

Panasonic BEP-NRH005 Series Instruction Manual

Hub dynamo

Advertisement

Available languages

Available languages

Quick Links

IMPORTANT
■ This manual contains safety information. Read manual completely before first using this product, and save this manual for future use.
IMPORTANT SAFETY INSTRUCTIONS
■ Explanation of symbols
WARNING
!
Denotes a potential hazard that could result in serious injury .
CAUTION
!
Denotes a hazard that could result in minor injury or damage to the unit or other equipment.
!
Check that the wheels are fastened securely before riding the bicycle. If the wheels are loose in any way, they
may come off the bicycle and serious injury may result.
Check that the lamp illuminates normally when riding at night time.
!
The hub dynamo generates an extremely high voltage. Touching the dynamo terminal may cause an electric shock.
Never touch the connection terminal of the hub dynamo directly while riding the bicycle or while the wheel is spinning.
Note:
According to the German regulation you need to use an OVP. This dynamo has not implemented an OVP function in to the inner housing.
Therefore, please do use an external OVP, the NKV006 approved by Panasonic, in case that your front light will not include OVP function inside.
Please do use the approved Panasonic OVP NKV006. Use an external overvoltage protector.
Do not disassemble the internal hub mechanism.
Do not apply any lubricant to the inside of the hub, otherwise the grease will come out and it may cause problems with conductivity.
If the hub nuts are screwed on too tight, or if one or the other is screwed tighter or looser than the other, the hub axle may be forced to turn.
Contact your dealer for repairs if the tire needs replacement or the hub nuts are loose.
Check the degree of parallel of the front fork end. If the front fork end is severely out of parallel, deformation of the hub axle may cause noise
from an obstruction inside the hub dynamo to be generated.
Be sure to install the hub dynamo to the front fork so that the side with the connection terminal is on the right when facing toward the front of
the bicycle. If the side with the connection terminal is facing toward the left, the hub dynamo may not turn properly while riding.
Lamps with electrical circuits such as automatic lamps may become damaged if the bicycle is ridden at high speeds.
If the lamp is frequently turned on when riding at high speed ranges, it will shorten the operating life of the bulbs.
Parts are not guaranteed against natural wear or deterioration resulting from normal use.
Putting Together the Front Wheel Mounting Assembly
1. Align the front wheel (hub dynamo) in its mounting position. As shown in the diagram. The connection terminal of the
hub dynamo should be on the side (when the bicycle is facing forward). The connection terminal should be positioned
between the front fork and the basket stay.
2. Assemble the fender stays and basket stays. Make sure that the hub washer and hub nut or volute spring and quick release nut
have been put on in the correct order.
3. Tighten the hub nut .
(1) Tighten the left and right hub nuts alternately, little by little, to course that the hub dynamo connection terminal do not
turn away from the correct orientation.
(2) The recommended hub nut tightening torque is 20-25N- m.
Basket stay
Hub dynamo
Hub dynamo
connection
   connection
Front fork
terminal
Hub dynamo
Hub dynamo
Fender stay
Tightening torque :
20-25N-m
Note:
When tightening the cap nuts, tighten the nuts alternately on both sides and do not concentrate all of the effort for tightening
and loosening the cap nut on one side of the wheel only, otherwise the hub axle may turn, which could excessively tighten or
loosen the lock nuts.
Instruction Manual
Hub Dynamo
Model No. BEP-NRH005 Series
WARNING
CAUTION
terminal
Front fork
Basket stay
Fender stay
Connection of the cables
Connect the cables as shown in the illustration below.
Note: Scrape away the paint from the lamp' s frame connection terminal and the lamp connection terminal when
connecting the cables.
Lamp
connection
terminal
Lamp cable
Connector cap
Lamp connection terminal
Hub dynamo connection
terminal
Note:
Connect so that the current from the hub dynamo flows through the cable from the lamp connection terminal of the hub dynamo
to the frame connection terminal.
To disconnect the lamp from the hub dynamo, remove the connector cover.
Connector
cover
Remove
Checking the lamp illumination
Rotate the front wheel and check that the lamp illuminations.
Note:
All our components have been designed for bicycles to be used on official public roads only.
Specifications
Model No.
Compatible
size
Hub washer
Voltage/Output
Hub nut (BC 3/8)
Representative in Europe:
Panasonic Europe Ltd.
Panasonic Testing Centre
Winsbergring 15, 22525 Hamburg, Germany
Note:
Compatible bulbs
Note:
Frame Connection
Do not switch over the frame cable and the light cable by
terminal
mistake. If the cables are connected incorrectly, the light
will not illuminate.
Twist the cable wires before connecting them so that they
Frame cable
stay together.
Recommended wire specifications.
Approx.
Approx.
12 mm
12 mm
Note:
Bend the cable wires and run
Frame
them along the grooves.
connection
terminal
Earth mark
Do not allow the cable wires
to touch each other.
Front fork
Cable
Connector
cover
Connect
BEP-NRH005 Series
Tire outer diameter
400-660 mm
Wheel
16-26 inch
6 V/3.0W
Manufacturer:
Suzhou Sanyo Electro-mechanical co.,Ltd,
No.1025 Sunwu Road, Xukou, Wuzhong District, Suzhou 215164, China
Frontlamp
Taillamp
6V-2.4W
6V-0.6W
6V-3.0W
Insulation
Wire
Type
Standed
Size(AWG)22
Wire
Diameter approx.0.8mm
Insulation
Diameter 1.8 - 2mm
Insert
Bend
Groove
Do not ride the bicycle while the connector cover
is removed, otherwise the cable might get caught
in the bicycle wheel.
When removing the bicycle wheel, first remove
the connector cover. If the cables are pulled
strongly, it may break the cable wires or cause
poor contacts. Furthermore, when installing
the wheel, first secure the wheel to the front forks
and then connect the connector cover.
9BF-P-P111-02400
S0117-0

Advertisement

loading

Summary of Contents for Panasonic BEP-NRH005 Series

  • Page 1 Connector cap Bend the cable wires and run Therefore, please do use an external OVP, the NKV006 approved by Panasonic, in case that your front light will not include OVP function inside. Frame Please do use the approved Panasonic OVP NKV006. Use an external overvoltage protector.
  • Page 2 Dieser Nabendynamo hat keinen Überspannungsschutz im Inneren der Nabe eingebaut. Falls Ihr zugelassenes Frontlicht nicht bereits einen Isolierung Durchmesser 1,8 - 2 mm Überspannungsschutz integriert hat, verwenden Sie den zugelassenen Überspannungsschutz Panasonic NKV006. Hinweis: Zerlegen Sie nicht den inneren Nabenmechanismus.