Page 1
BALZER BALZER INC. INC. MOUNTAIN LAKE Vertical Lagoon Pumps Vertical Lagoon Pumps Vertical Lagoon Pumps Vertical Lagoon Pumps USER MANUAL FOR VERTICAL LAGOON PUMP USER MANUAL FOR VERTICAL LAGOON PUMP...
This new Balzer Inc. product is designed and manufactured to give years of very dependable service when used for the purpose for which it is intended, and when properly maintained.
CERTIFICATE OF GENERAL EQUIPMENT WARRANTY Balzer Inc. warrants new Products sold by it to be free from defects in material or workmanship for a period of one (1) year after date of delivery to the first user and subject to the following conditions.
Safety BALZER INC. 4. When the decal has been attached in place, use a SAFETY SIGNS cloth or soft paper towel to burnish the decal onto the cleaned surface. Work gently from the middle SAFETY SIGNS ARE IMPORTANT outwards to avoid creating any wrinkles.
Page 7
Always use a safety chain between the site, outside the unit and with proper life support towing vehicle and pump on public roadways. system. Contact your BALZER dealer for more information before you enter a tank. 15. Hydraulic pressure can be very dangerous and can cause serious personal injury and death.
Parts BALZER INC. IT IS THE POLICY OF BALZER COMPANY TO CONSTANTLY IMPROVE ITS PRODUCTS WHENEVER IT IS PRACTICAL TO DO SO. THEREFORE, BALZER C OMPANY RESERVES THE RIGHT TO REDESIGN OR CHANGE ITS EQUIPMENT OR COMPONENT PARTS THEREOF WITHOUT INCURRING THE OBLIGATION TO INSTALL OR FURNISH SUCH CHANGES ON EQUIPMENT PREVIOUSLY DELIVERED.
Operation BALZER INC. With the tractor’s throttle at idle, check OPERATING & MAINTENANCE the pump rotation by engaging the control lever. Remember which Site-Preparation: direction the control lever was moved to produce proper impeller rotation. If it is Location of the pump is generally...
Page 11
(overnight or during periods of CONTINUED... inactivity exceeding one hour), remove or raise the pump out of the lagoon in around the hydraulics portion of the pump. order to prevent the internal gearbox A light coating of oil is recommended to from water contamination.
Lubrication & Maintenance BALZER INC. All Maintenance shall be carried out by a competent operator after disconnecting the PTO from the tractor. An adequate lubrication and the use of suitable lubricants are both essential for the long life and correct operation of the machine. Keep oil level visible in the sight glass. (Use 90W oil) Make sure all screws and bolts have been tightened, and the bolts are in the correct position after the first 4 hours of operation and regularly there after.
58 FOOT LAGOON PUMP GREASE POINTS Grease wheel bearings after removing Grease wheel bearings after removing pump from lagoon to displace moisture. pump from lagoon to displace moisture. Also, grease bearings every season. Also, grease bearings every season. DO NOT OVER GREASE - 1 PUMP ON GREASE...
48 FOOT LAGOON PUMP GREASE POINTS Grease wheel bearings after removing pump from lagoon to displace moisture. Also, DO NOT OVER GREASE - 1 PUMP ON GREASE grease wheel bearings every season. GUN PER GREASE POINT WILL SUFFICE Grease All 5 Bearings at ‘A’ Points Daily Grease All 5 Slip Yokes at ‘B’...
38 FOOT LAGOON PUMP GREASE POINTS Grease wheel bearings after removing pump from lagoon to displace moisture. Also, grease wheel bearings every season. DO NOT OVER GREASE - 1 PUMP ON GREASE GUN PER GREASE POINT WILL SUFFICE Grease All 4 Bearings at ‘A’ Points Daily Grease All 4 Slip Yokes at ‘B’...
32 FOOT LAGOON PUMP GREASE POINTS Grease wheel bearings after removing pump from lagoon to displace moisture. Also, grease wheel bearings every season. DO NOT OVER GREASE - 1 PUMP ON GREASE GUN PER GREASE POINT WILL SUFFICE Grease All 5 Bearings at ‘A’ Points Daily Grease Slip Yoke at Point ‘B’...
3 - WAY VALVE ASSEMBLY ITEM N O. QTY. PART NO. DESCRIPTION 1249 .5" x 1.25" Hex Head Bolt 20699 Cover - 7" Square Fl a nge 1255 .5" x 2.75" Hex Head Bolt 21479 .53" x 4.62" x .075" Washer 4114 6.75"...
WEASLER LAGOON PTO - 1 3/8” 21 SPLINE, PART #26867 10 11 PHASE 39.75 [1009.7] CENTERLINE TO CENTERLINE COMPRESSED (REF.) 59.13 [1501.8] CENTERLINE TO CENTERLINE EXTENDED w/5.00 [127] LAP GREASE @ 39.75 [1009.7] CENTERLINE TO CENTERLINE 2x .375 - 16 UNC .38 [9.5] x .19 [4.8]...
Page 30
WEASLER LAGOON PTO - 1 3/4” 20 SPLINE, PART #26868 10 11 PHASE 39.75 [1009.7] CENTERLINE TO CENTERLINE COMPRESSED (REF.) 59.13 [1501.8] CENTERLINE TO CENTERLINE EXTENDED w/5.00 [127] LAP GREASE @ 39.75 [1009.7] CENTERLINE TO CENTERLINE 2x .375 - 16 UNC .38 [9.5] x .19 [4.8]...
Page 31
PTO LUBRICATION SPECIFICATIONS TELESCOPING MEMBERS CROSS & BEARING GREASE POINT CROSS & GREASE POINT BEARING GREASE POINT LUBRICATE ALL FITTINGS WITH A GOOD QUALITY LITHIUM SOAP BASE E.P. GREASE MEETING THE N.L.G.I. #2 SPECIFICATIONS AND CONTAINING NO MORE THAN 1% MOLYBDENUM DISULFIDE. (EX. SHELL SUPER DUTY OR EQUIVALENT) AN E.P.