Zepter NEB-01-C Instructions For Use Manual

Zepter NEB-01-C Instructions For Use Manual

Portable mesh

Advertisement

Quick Links

Instruction for Use
Portable Mesh
Nebulizer
NEB-01-C

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NEB-01-C and is the answer not in the manual?

Questions and answers

Summary of Contents for Zepter NEB-01-C

  • Page 1 Instruction for Use Portable Mesh Nebulizer NEB-01-C...
  • Page 2: Table Of Contents

    Contents 1. Safety Notes 2. Disposal 3. Item Description 3.1 Content of Packaging 3.2 Device Description 4. Instruction for Use 4.1 Before First Use 4.2 Installation 4.3 Charging 4.4 Instruction for Use 4.5 Nebulization 5. Cleaning and Disinfection Method 10-11 6.
  • Page 3: Safety Notes

    1. Safety Notes Before using the appliance for the first time, read the Instructions for Use carefully and ensure you comply with the safety instructions! • The appliance must only be used as described in these instructions. The manufacturer is not liable for damages arising from any use contrary to the intended purpose.
  • Page 4: Disposal

    Do not expose the nebulizer and accessories to corrosive liquids and gases. Do not wrap the power cord around the unit. Do not use nebulizer near a heating device or open flame. Do not use a microwave oven, fan or hair dryer to dry or disinfect the nebulizer or accessories.
  • Page 5: Item Description

    Warning: Do not dump batteries into fire. Never incinerate or dispose of batteries in fire as they may explode. This is very dangerous and prohibited. For your own safety, don’t remove the battery from the product and please contact only authorized Zepter Service Centre. 3. Item Description 3.1 Content of Packaging...
  • Page 6: Instruction For Use

    4. Instruction for Use 4.1 Before First Use 1. Remove all packaging from the main device and accessories. 2. Verify if all content is intact. 3. Charge the appliance minimum for 30 min before first use. 4.2 Installation Note: Clean, disinfect and dry all parts before installation 4.3 Charging 1.
  • Page 7: Charging

    Note! Before charging, make sure it is normally charged through the connected socket. Note! This device is independent charging, do not use any other electronic equipment for charging. 4.4 Instruction for Use Description of indicators Blue light keeps on (uniform nebulization mode) Working Blue light flashes (microwave mode)
  • Page 8: Nebulization

    1. Clean and disinfect the component and spray nozzle medication cup before each use. 2. Inject the liquid: Open the cap by turning it counterclockwise, inject the solution and return the cap by turning it clockwise. Note! Add the liquid before turning on the device.
  • Page 9 b. By mask c. By mouthpiece a. Direct inhalation 6) Slowly take a deep breath and then breathe in the medication. 7) The nebulizer can set the working time to 10 minutes, and it will shut down automatically after 10 minutes.
  • Page 10: Cleaning And Disinfection Method

    5. Cleaning and Disinfection Method After each use, it is necessary to clean and disinfect the cup components (including spray nozzle, medication cover), mask and mouthpiece. The specific methods of cleaning and disinfection are recommended as follows: 1. Cleaning Please turn o the power when cleaning the device. Do not connect the device with power supply. 1) Remove the components from the main unit: the medication cup components (including the spray nozzle, medication cover), the inhalation mask or the mouthpiece, and soak them in clean warm water (which is no more than 40 degrees centigrade) for about 5 minutes.
  • Page 11: Technical Data

    5. Technical Data Product name Portable Mesh Nebulizer Product Item code NEB-01-C Type of battery Li-ion battery, DC2.4V, 2x500mAh, 1.2 Wh Charging time Approx. 2 hrs Usage time...
  • Page 12: Trouble Shooting Guideline

    7. Trouble Shooting Guideline 1) Check whether the nebulizer is charged. If the blue and Does not work when green indicators are always on, recharge the device. turned on 2) Check if the medication cup has been fully filled. 1) Check if the medication cup has been filled with the right medication, which should be water soluble and non-corrosive.
  • Page 13: Declaration Of Conformity

    The manufacturer undertakes to repair or replace cost-free within the warranty period those parts that prove to have manufacturing defects. Those defects that are not clearly attributable to either material or the manufacturing will be examined at one of ZEPTER Service Centres or at our headquarters and charged according to the outcome.
  • Page 14 Attention! If, after the purchase of the product, its label with serial number has been removed or is not recognizable, the manufacturer reserves the right to refuse the warranty service. If you have any comments or questions concerning the functioning of the device or warranty, please contact your ZEPTER Sales Representative.

Table of Contents