Summary of Contents for BTR BCR - 2 A
- Page 1 Installation and Commissioning Instructions ontrol RWA-Control Unit BCR - 2 A / 4 A / 8 A / 12 A...
- Page 2 ontents Abbreviations Warning and Safety Symbols Target Groups, Intended Use Safety Instructions 3 - 8 Data sheet RWA Control Unit BCR - Data sheet RWA Control Unit BCR - Data sheet RWA Control Unit BCR - 12 A Data sheet RWA Control Unit BCR - 12 A 9 - 10 Technical Data Preparing assembly...
-
Page 3: Index Of Abbreviations
reliminary emark bbreviations Index of abbreviations Scale units These abbreviations are used consistently throughout these °C Degree Celsius assembly & operating instructions. Unless stated differently, all Amps dimensions indicated in this document are in mm. Amp-hours General tolerances in accordance with DIN ISO 2768-m. Kilogram Surface mounting Metres... -
Page 4: Target Group
Btr, is released for its proper use at a own responsibility and detect or minimize possible power-operated window for the following use: remaining risks. - Page 5 reliminary emark The need for a risk assessment at the installation site • the installation height of the drive or of the „HSK / main due to the reasonably foreseeable misuse. closing edge“ (parallel to hinge) < 2,5 m above the floor A risk assessment in accordance with the Machinery and one of the following conditions: Directive 2006 / 42 / EG by activation of the power-...
-
Page 6: Safety Instructions
• Control of electromotive window drives for smoke in the factory. btr shall not assume and heat exhaust in case of fire and for “natural liability for the system-compatible func- ventilation”. - Page 7 afety nstruCtions The power line on-site must be secured sepa- It is imperative that the information rately and provided with all poles separators. provided in the installation instructions arning After opening of the system housing voltage of the controlled window drives are ob- carrying parts are exposed.
-
Page 8: Ambient Conditions
afety nstruCtions Ambient conditions uidelines and tandards The product may not be subjected to impacts or falls, or The most recent state of country-specific laws, regulations, to vibrations, moisture, aggressive vapors or other harmful provisions and standards must absolutely be observed du- environments, unless the manufacturer released it for one ring the installation and for electrical connections. -
Page 9: Data Sheet
: 2 A heet rWa - c BCR - 2 A ata sheet ontrol Control Unit BCR 2 A - 0101 Article Application Compact Control Unit for smoke and heat exhaust ventilation systems operating with 24 V DC voltage, suitable for staircases. - Page 10 : 8 A 12 A heet rWa - c BCR - 8 A ata sheet ontrol 12 A Control Unit BCR 8 A - 0102 Article Application Compact Control Unit for smoke and heat exhaust ventilation systems operating with 24 V DC voltage, suitable for staircases. Technical Data (Rated values) Part.-No.
-
Page 11: Technical Data
reParing ssembly echnical reparing assembly Important instructions for safe assem- Electrical data and connected loads arning bly: Fully observe all instructions, incorrect assembly may lead to serious injuries. Operating voltage, primary: 195…..253 V AC Frequency 50….60 Hz Before starting the installation please check with the delivery note that the delivery is complete and correct, any complaints received Nominal current Version... - Page 12 reParing ssembly onnection acilities abling 12 A min. 3 x A Cable: 5 x 1,5 or 7 x 1,5 mm (see formula) Length: max. 200 m Cable: 2 x 2 x 0,8 mm Length: max. 400 m Cable: 2 x 2 x 0,8 mm Length: max.
-
Page 13: I Nstallation Step
nstAllAtion step onneCting rives anD entilation nstAllAtion step BCR 2 A BCR 4 A c onnecting rives and entilation Connection of drives and ventilation: BCR 2 A - 0101 and BCR 4 A - 0101 close close reset red: open green: close Drive 1 Fault... - Page 14 nstAllAtion step onneCting rives anD entilation nstAllAtion step 12 A BCR 8 A BCR 12 A c onnecting rives and entilation Connection of drives and ventilation: BCR 8 A - 0102 and BCR 12 A - 0102 reset red: open green: close Drive 1 Drive 2...
- Page 15 nstAllAtion step onneCting moke eteCtors anD reakglass nits nstAllAtion step 12 A onnection utomatic and anual moke etectors Connection of automatic and manual smoke detectors / BMZ (same as HSE reset) reset red: open green: close Drive 1 Drive 2 Fault Alarm (inverted)
- Page 16 nstAllAtion step onneCting inD anD ensors nstAllAtion step 12 A onnecting ensors and ensors Connection of wind sensors and rain sensors Wind-Speed (reshold) [m/s] wind open open close close Reset Button (same as HSE reset) reset wind red: open green: close Drive 1 Drive 2 1 2 3 4 5...
-
Page 17: Connection Of Power Supply
nstAllAtion step onneCting oWer uPPly nstAllAtion step BCR 2 A BCR 4 A c onnecting oWer upply Connection of power supply Operating voltage, primary 195 ... 253 V AC Power Supply 24V Battery Wind-Speed (reshold) [m/s] wind open open Battery close close reset... - Page 18 nstAllAtion step onneCting oWer uPPly nstAllAtion step 12 A BCR 8 A BCR 12 A c onnecting oWer upply Connection of power supply Operating voltage, primary 195 ... 253 V AC Power Supply 24V Battery Wind-Speed (reshold) [m/s] wind open open Battery close...
- Page 19 nstAllAtion step leD´ DiP s s anD WitChes nstAllAtion step LED´ dip s s and Witches LED`s from motherboard LED`s from breakglass unit (HSE) Emergency- State Operation Fault OPEN Standby Emergency-OPEN / alarm (power supply operation) Emergency-OPEN / alarm (back-up accumulators mode) flashes flashes Power failure (highest priority)
-
Page 20: Completing Installation
nstAllAtion step nabling Peration omPleting nstallation roublshooting 6: e nstAllAtion step nabling operation completing installation Before the installer is allowed to enable the operation of the Control Unit, We advise to perform an insulation measurement of the cable network the complete performance range of the system must be checked with before enabling operation of the plant and to keep a written record of utmost care. - Page 21 uses uses Fuse RWA - Control Unit BCR (accumulators) Automotive Blade Fuse 5,2 x 0,64 mm BCR 2A - 0101 Glass Cartridge Fuse 5 x 20 mm 3,15 AT (drives) Glass Cartridge Fuse 5 x 20 mm (accumulators) BCR 4A - 0101 6,3 AT (drives) 10 A...
- Page 22 nDiCator anD ontrol lements ndicator and ontrol lements Position in the Control Unit Meaning of the Displays (overview) The indicators and control elements (switches) are in the Basically, the green indicator „B“ signals that the Con- same position on all BCR versions. trol Unit works properly.
-
Page 23: I Mportant Maintenance Information
A sample maintenance contract can be downloaded from • When connecting wind and rain sensors check for proper functionality the homepage of of the sensors, readjust the wind response threshold, if necessary. Btr G The service instructions for the connected components are decisive (www.btr-hamburg.de). for their maintenance. - Page 24 emounting iability isPosal emounting and dismantling iability We reserve the right to change or discontinue products at any time The Control Unit shall be stored only in locations protected from mois- ture, severe contamination and temperature fluctuations (not beyond without prior notice. Illustrations are subject to change. Although we take 30°C).
- Page 25 otes RWA - Control Unit BCR...
- Page 26 otes RWA - Control Unit BCR...
- Page 27 Offenders will be held liable for the payment of damages. All rights reserved in the case of a patent award or utility model registration. Basically the General Terms and Conditions of Btr GmbH apply to all offers, supplies and services.
- Page 28 ♦ BTR GmbH ♦ ♦ Gemeindewald 11 ♦ D-86672 Thierhaupten ♦ ♦ Telefon: +49 8271 811 92-0 ♦ Fax: +49 8271 811 92-55 ♦ www.btr-hamburg.de 9000032851_V0.3_KW16/21...