Advertisement
Quick Links
Drift Master
Installation Manual
Tech Support: 800.332.4094 Option 2
2072 Alton Parkway. Irvine, CA 92606
Website: Lagunatools.com
Copyright 2017 Laguna Tools, Inc. – Laguna is a registered trademark of Laguna Tools, Inc.
All documentation subject to change without notice
Advertisement
Summary of Contents for Laguna Tools Drift Master
- Page 1 Drift Master Installation Manual Tech Support: 800.332.4094 Option 2 2072 Alton Parkway. Irvine, CA 92606 Website: Lagunatools.com Copyright 2017 Laguna Tools, Inc. – Laguna is a registered trademark of Laguna Tools, Inc. All documentation subject to change without notice...
- Page 2 Hardware A. Main Bracket (2) B. Table nut (2) C. Table Bolt (2) D. Fence Bolt (2) E. Washer (4) F. Nut (2) Note: Please make sure that all of the mounting hardware is accounted for. Note: Inspect all parts for defects prior to assembly. Note: Ruler included in package may not fit on all bandsaws.
-
Page 3: Installation
Installation **There are three techniques for mounting the fence. Please review all three prior to mounting and choose the best method for your saw** Installing the brackets to the table (Technique 1) All documentation subject to change without notice... - Page 4 1. Using hardware (B), (C) and (E) mount the main brackets (A) to the bandsaw table. See figure 1.1 & 1.2 Figure 1.1 Figure 1.2 You may need to enlarge the current holes in your Note: table. They should be ½” to accept the bolt provided. All documentation subject to change without notice...
- Page 5 2. Mount fence bolt (D) using hardware (E) and (F). Do not fully tighten nut (F) yet. See figure 2.1 & 2.2 Figure 2.1 Figure 2.2 All documentation subject to change without notice...
- Page 6 Note: Prior to mounting the fence rail choose the stud holes in the rail that are best suited for your bandsaw. You should have four sets of holes to choose from. Note: To utilize the full throat of the saw use the rail holes that will allow the crank handle to be as far left of the saw frame as possible.
- Page 7 Note: Adjust height of drift master on brackets so the fence rides on the bandsaw table surface. 4. Adjust bolts (D) in bracket slots until drift master fence rides on bandsaw table. Tighten nuts (F) once this is done. 5. Tighten all hardware.
- Page 8 Installing entire fence with brackets already attached (Technique 2) 1. Attach brackets using supplied hardware. Note: Do not tighten nut (F) 2. Fully seat bolt (D) into rail. This will enable you to tighten nut (F) without the use of a wrench on bolt (D) once fence is mounted to saw.
- Page 9 Installing without the use of brackets (Technique 3) 1. Remove the original fence system, figure 1.1 Figure 1.1 Figure 1.2 End of ruler must not protrude Drill and tap for ruler past blade slot Drill and tap holes for the ruler indicated in figure 1.2. Note: hole placement will vary from one machine to another.
- Page 10 Adjustments To adjust the drift on the drift master loosen the top handles, figure Figure 2.1 Figure 2.2 Turn bottom knob till desire adjustment is achieved then tighten handles. 2.2 Move the quick release to lock and unlock the screw mechanism. This will allow free movement of the fence for large adjustments in unlocked position.
- Page 11 B50.01.00.00.00 RIP FENCE WITH FINE MOVING В50.01.00.00.04 ALUMINUM PROFILE DIN 985 NUT М 12 DIN 125 A WASHER АМ12 В50.01.00.00.02 STUD В50.01.00.00.05 COTTER GN603-78-М10-DGN HANDLE М10 DIN 134 WASHER M10 В50.01.00.00.06 DIN 134 WASHER M 8 GN603-63-М8-45-DGN HANDLE М8Х45 В50.01.00.00.07 CENTERING STUD В50.01.00.00.03 SLIDE BLOCK FOR FENCE...
- Page 12 ART.139-60-8.5 HANDLE 8.5 DIN 912 SCREW М 8Х65 DIN 439 NUT М12 LOW TAB. T1144 PLATE B50.01.10.00.07 BUSHING В50.01.00.00.09 ECCENTRIC ISO 7380 SCREW М 6Х10 B50.01.10.00.03 DIN 603 SCREW М8X25 B50.01.10.00.04 ROTATING STRIP DIN 134 WASHER M 8 DIN 315 FLYING NUT M8 DIN 125 A WASHER АМ12...
- Page 13 Laguna Tools is not responsible for errors or omissions. Specifications subject to change. Machines may be shown with optional accessories. © 2017, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved.