1. Manuals
  2. Brands
  3. Diamond Manuals
  4. Network Router
  5. DSL602EU
  6. User manual

Diamond DSL602EU User Manual

Adsl2+ usb ethernet combo bridge router freeway dsl
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DSL602EU User's Manual
ADSL2+ USB Ethernet Combo Bridge Router
Freeway DSL DSL602EU User's Manual
Rev. 1.0
Dec. 2008

Advertisement

Table of Contents
loading

Related Manuals for Diamond DSL602EU

Summary of Contents for Diamond DSL602EU

  • Page 1 DSL602EU User’s Manual ADSL2+ USB Ethernet Combo Bridge Router Freeway DSL DSL602EU User’s Manual Rev. 1.0 Dec. 2008...

  • Page 2: Table Of Contents

    ESCRIPTION ....................3 ORTS AND UTTONS DSL602EU ..................3 NSTALLING YOUR INSTALLING USB DRIVER (OPTIONAL) ............... 4 CONFIGURING TCP/IP....................5 SETTING UP YOUR DSL602EU..................6 DSL602EU..................6 OGIN TO WEB CONFIGURATION ....................7 ......................... 7 VERVIEW 6.1.1 Overview ......................7 6.1.2...

  • Page 3: Introduction

    Conforms to TR-069 CPE WAN Management Protocol 1.2 System Requirement In order to use the DSL602EU, you must have the following: ADSL service up and running on your telephone line, with at least one public Internet address for your LAN...

  • Page 4: Dsl602Eu Overview

    DSL602EU User’s Manual DSL602EU Overview 2.1 LED Description The front panel contains lights called LEDs that indicate the status of the modem. Color Status Description The device is power on. Green POWER The device is power off. The device is booting up.

  • Page 5: Ports And Buttons

    DSL602EU via the web interface. To reset the DSL602EU, simply press the reset button for more than 5 seconds. The DSL602EU will be reset to its factory defaults and after about 30 seconds the DSL602EU will become operational again.

  • Page 6: Installing Usb Driver (Optional)

    DSL602EU User’s Manual Installing USB Driver (optional) You must install the USB driver before you can use the DSL602EU via an USB connection. Please follow the steps below (may vary for each computer) to complete the USB driver installation on a Windows 2000/XP operating system.

  • Page 7: Configuring Tcp/Ip

    4. Configuring TCP/IP This section will help you to establish a connection between a PC and the DSL602EU. Each computer that will be part of your network needs to communicate with the DSL602EU. To do this, you may need to configure each PC’s network settings to automatically obtain an IP address.

  • Page 8: Setting Up Your Dsl602Eu

    DSL602EU User’s Manual Setting up Your DSL602EU This section guides you through configuring your DSL602EU. You should have your computers configured for DHCP mode and have proxies disabled on your browser. If you do not get the page as shown below, you may need to delete your temporary Internet files by flushing the cached web pages.

  • Page 9: Web Configuration

    DSL602EU User’s Manual Web Configuration 6.1 Overview 6.1.1 Overview This page displays the firmware version, SDK version, interfaces status and Internet connection status.

  • Page 10: Dhcp Clients

    DSL602EU User’s Manual 6.1.2 DHCP Clients This page displays the client devices which are assigned IP addresses by the DSL602EU.

  • Page 11: System Log

    DSL602EU User’s Manual 6.1.3 System Log The page records various types of activity on the DSL602EU. You can view data generated or acquired by routine system communication with other devices, such as the results of negotiation with the ISP and so on. This...

  • Page 12: Internet

    DSL602EU User’s Manual 6.2 Internet 6.2.1 Internet Connection The DSL602EU supports multiple channel operation modes. It is bridge mode enabled by factory default. There is a 1483-bridged mode with PVC 0/33 in the system.
  • Page 13 DSL602EU User’s Manual You can click the Edit icon ( ) to edit the default configuration; click the Remove icon ( ) to delete the current configuration, or click New Connection button to create a new connection. Bridge Mode Click New Connection button.
  • Page 14 DSL602EU User’s Manual 1483 MER (Mac Encapsulating Routing) Mode Click New Connection button. Select the Operating Mode to be Router Mode (PPPoE, PPPoA MER, 1483 Routed). Select the Channel Mode to be MER. Set the parameters VPI/VCI and Encapsulation mode according to the CO DSLAM’s setting.

  • Page 15: Statistics

    DSL602EU User’s Manual 6.2.2 Statistics 6.2.3 WAN This page shows the WAN statistics information.

  • Page 16: Atm

    DSL602EU User’s Manual 6.2.4 ATM This page shows the ATM interface statistics information.

  • Page 17: Adsl

    DSL602EU User’s Manual 6.2.5 ADSL This page shows the ADSL status and statistics.

  • Page 18: System

    DSL602EU User’s Manual 6.3 System 6.3.1 Password The first time you log into the system with default password. This page allows you to change the password for administrator. Field Description Old Password Enter the old password in this field. New Password Enter the new password in this field.

  • Page 19: Network Time

    SNTP servers. This page allows you to manually configure the time and select Time Zone. Also, you can enable SNTP client update function and configure the SNTP server to let the DSL602EU synchronize with the public SNTP servers.

  • Page 20: Store/Restore Settings

    6.3.3 Store/Restore Settings This page allows you to backup current settings to a file or restore the settings from a previously saved file. Also, you can reset the DSL602EU to default settings. To save settings to a file, just click the Save button to save the file to a local drive.

  • Page 21: Firmware Update

    DSL602EU User’s Manual 6.3.4 Firmware Update The system software used by this DSL602EU is called “firmware”. This page allows you to upgrade the firmware to a newer version. To upgrade the firmware, please follow the instructions below: Click the Browse button to select the firmware file.

  • Page 22: Save Settings/Reboot

    To save your changes permanently, just click the Save settings/Reboot button to start rebooting. IMPORTANT! DO NOT power off the DSL602EU or press the Reset button while this procedure is in progress.

  • Page 23: Lan

    Enter the IP address of DSL602EU. Subnet Mask Enter the subnet mask for this network. DHCP Server If Enabled, the DSL602EU will assign IP addresses to PCs (DHCP clients) on your LAN when they start up. The default setting is Enabled. Start/End IP...
  • Page 24 DSL602EU User’s Manual To assign a static IP to a DHCP client, please follow the instructions below: Click Add Entries to display DHCP Static IP Lease page. Enter the MAC address and specify a static IP address to the client.

  • Page 25: Statistics

    DSL602EU User’s Manual Statistics The page shows the received/transmitted statistics of WAN, Ethernet and USB.

  • Page 26: Dsl

    6.4.2 DSL This page allows you select the modulation, phone line type and capability that you want DSL602EU to support. The default configuration in this page can work with most ADSL implementations. DO NOT change any setting unless you have been instructed.

  • Page 27: Network Information

    6.4.3 Network Information 6.4.3.1 ARP Table This page shows the ARP Table of DSL602EU’s LAN port. ARP (Address Resolution Protocol) maps the IP address to the physical address, labeled HW Address (the MAC address) and helps to identify computers on the LAN.

  • Page 28: Routing Table

    DSL602EU User’s Manual 6.4.3.2 Routing Table This page shows the Routing Table of DSL602EU.

  • Page 29: Network Settings

    6.4.4.1 Default Gateway Check the Enable Automatic Assigned Default Gateway checkbox to allow the DSL602EU to accept the first received default gateway assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s). If the checkbox is not selected, enter the static default gateway and/or a WAN interface.

  • Page 30: Static Routing

    DSL602EU User’s Manual 6.4.4.2 Static Routing This page allows you to configure computers that are connected to the DSL602EU to communicate with computers on another LAN segment (e.g. 192.168.0.1) which are connected to the DSL602EU via another router. Field Description Destination Configure the destination address of LAN IP.

  • Page 31: Igmp

    DSL602EU User’s Manual 6.4.4.3 IGMP The page allows you to enable or disable the IGMP (Internet Group Management Protocol) snooping function. IGMP is used to establish the multicast groups to forward the multicast packet to the member ports. It can very effectively reduce multicast traffic from streaming and other bandwidth intensive IP applications.

  • Page 32: System Log Configuration

    6.4.5 System Log Configuration This page allows you to configure the system log level and display level. You must enable the System Log function so that the DSL602EU can record the related logs. To configure System Log function, please follow the instructions below: Click Enable radio button and select Log Level and/or Display Level from the drop-down list.
  • Page 33 DSL602EU User’s Manual Field Description Select enable to log all the select events. Log Level Select the log level. All events above or equal to the selected level will be logged. Display Level Select the display level. All logged events above or equal to the selected level will be displayed.

  • Page 34: Device Management

    6.4.6.1 Service You can enable or disable which management services being used in your DSL602EU’s LAN interface. You need to configure at least one WAN interface (except Bridge) before settings up service control list on WAN interface. Access Service is not available for Bridge mode.

  • Page 35: Ip Address

    DSL602EU User’s Manual 6.4.6.2 IP Address The IP Address Access Control mode, if enabled, permits access to local management services from IP addresses contained in the Access Control List. If the Access Control mode is disabled, the system will not validate IP addresses for incoming packets.
  • Page 36 DSL602EU User’s Manual To configure the IP address for Access Control mode, please follow the instructions below: Click Add button to enter Access Control page. Enter the specific IP address which will be granted access and then click Save/Apply button.

  • Page 37: Upnp

    The DSL602EU supports a control point for Universal Plug and Play (UPnP), and supports two key features: NAT Traversal and Device Identification.
  • Page 38 DSL602EU User’s Manual 6.4.6.4 TR-069 The TR-069 (CPE WAN Management Protocol) function can secure remote host access to your DSL602EU from LAN interface for some services provided by it. Field Description Inform Enable/disable the DSL602EU to connect to the ACS periodically.
  • Page 39 DSL602EU. Request User Name Connection Enter the password used to authenticate an ACS making a connection request to the DSL602EU. Request Password Click this button to force the DSL602EU to immediately GetRPCMethods establish a connection to the ACS.

  • Page 40: Diagnostics

    DSL602EU User’s Manual 6.4.7 Diagnostics This page shows the ADSL tone diagnostic information. You will not typically need to view this data, but you may find it helpful when working with your ISP to diagnose network and Internet data transmission problems.

  • Page 41: Wall Mounting (Optional)

    DSL602EU User’s Manual Wall Mounting (Optional) This product can be mounted on wall. There are two holes in the lower case and you can use the screws to mount the device.

  • Page 42: Appendix A. Troubleshooting

    Refer to the Quick Start Guide for more details. Check to see that the LAN, DSL and Internet LEDs are lit. Check the settings on your PC and DSL602EU. Again, refer to the Quick Start Guide for more details.
  • Page 43 Verify that the phone line is connected directly to the wall and to the line input on the DSL602EU. If the DSL602EU is connected to the wall line outlet via a splitter, make sure you connect the DSL602EU to the port labeled MODEM.

  • Page 44: Appendix B. Specifications

    DSL602EU User’s Manual Appendix B. Specifications ADSL G.994 Compliance G.992.1 (G.dmt), supporting Annex A, B and I G.992.2 (G.lite) ANSI T1.413 G.992.3 (ADSL2), Annex J/K (SADSL), Annex L (REDSL), Annex M (Sym-DSL) G.992.5 (ADSL2+) ATM protocols Up to 8 PVCs Adaptation Layers AAL5, AAL2 and AAL0 are supported.

Table of Contents