Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for JPE CRYO BEARING STAGE
Summary of Contents for JPE CRYO BEARING STAGE
- Page 1 MAN01-03 – C (CBS) U EARING TAGE ANUAL CRYO & NANO PRODUCTS Page 1 / 11 +31 (0) 43 3585 777 Property of: JPE Last update: 2021-07-05 www.jpe.nl Author: JPE Revision: 03 Aziëlaan 12 Filename: CNP_MAN01-03_R03_CBS.docx Doc status: Released 6199 AG Maastricht-Airport...
-
Page 2: Table Of Contents
INSIDE THE BOX MOUNTING INSTRUCTIONS CONNECTING TO THE CONTROLLER Drive signal Position sensor signal Connecting to Controller SENSOR CALIBRATION DECLARATION OF CONFORMITY Page 2 / 11 Property of: JPE Last update: 2021-07-05 Author: JPE Revision: 03 Filename: CNP_MAN01-03_R03_CBS.docx Doc status: Released... - Page 3 CBS_Brochure.pdf (JPE) DOCUMENT HISTORY Author Date Comment 2019-06-20 R01. Creation. 2021-02-01 R02. Update. 2021-07-05 R03. Update. DEFINITIONS Definition Description ABBREVIATIONS Abbreviation Description Page 3 / 11 Property of: JPE Last update: 2021-07-05 Author: JPE Revision: 03 Filename: CNP_MAN01-03_R03_CBS.docx Doc status: Released...
-
Page 4: Introduction
1. INTRODUCTION Thank you for using JPE’s Cryo & Nano Products! This User Manual describes the handling and use of Cryo Bearing Stage (CBS), from here on described as positioner). Please read this document carefully prior to installation and (initial) operation of the controller, (stand-alone) positioners, actuators and stages. -
Page 5: Inside The Box
Figure 3: Example packaging with 1x CBS10-RLS XYZ configuration Unpacking XY(Z) configuration require a bit more attention as it can be easy to damage cabling (flex PCB) or connectors. Page 5 / 11 Property of: JPE Last update: 2021-07-05 Author: JPE Revision: 03 Filename: CNP_MAN01-03_R03_CBS.docx... -
Page 6: Mounting Instructions
An XY configuration is possible without any the use of additional parts. For an XYZ configuration, an additional Z-bracket (I1-CBS10) can be purchased. In either configuration (XY or XYZ), the positioners will be delivered already pre-configured as such. Page 6 / 11 Property of: JPE Last update: 2021-07-05 Author: JPE Revision: 03 Filename: CNP_MAN01-03_R03_CBS.docx... -
Page 7: Connecting To The Controller
Please note that (Piezo) REF is NOT the same as (system) GND or PE, so do not connect these to each other and do not use standard oscilloscope probes! Because of design constraints, open voltage contacts are present! Page 7 / 11 Property of: JPE Last update: 2021-07-05 Author: JPE Revision: 03 Filename: CNP_MAN01-03_R03_CBS.docx... -
Page 8: Position Sensor Signal
RSM Input A CBSx-RLS XY – (Y) RSM Input B CBSx(-RLS) XYZ – (X) CADM2 Output For available Modules see CNP-Products MAN01-09 (CPSC). Page 8 / 11 Property of: JPE Last update: 2021-07-05 Author: JPE Revision: 03 Filename: CNP_MAN01-03_R03_CBS.docx Doc status: Released... - Page 9 CBSx-RLS XYZ – (X) RSM Input A CBSx-RLS XYZ – (Y) RSM Input B CBSx-RLS XYZ – (Z) RSM Input C Page 9 / 11 Property of: JPE Last update: 2021-07-05 Author: JPE Revision: 03 Filename: CNP_MAN01-03_R03_CBS.docx Doc status: Released...
-
Page 10: Sensor Calibration
(free movement required) and storing measurement calibration values. This can all be done with the user software, please read the Software User Manual (MAN02) on how to do this. Page 10 / 11 Property of: JPE Last update: 2021-07-05 Author: JPE Revision: 03 Filename: CNP_MAN01-03_R03_CBS.docx... -
Page 11: Declaration Of Conformity
2014/35/EU Low Voltage Directive 2014/30/EU EMC Directive 2011/65/EU RoHS A copy of the Technical file for this equipment is available at JPE. Maastricht-Airport, 29 June 2018 Ir. H. Janssen Founder & CEO JPE B.V. The Netherlands Page 11 / 11...
Need help?
Do you have a question about the CRYO BEARING STAGE and is the answer not in the manual?
Questions and answers