Page 8
Contents Assembly of rear main board Assembly of front main board Assembly of rope Assembly of pendulum Assembly of pointer Troubleshooting Parts list of Galileo pendulum clock...
Page 10
TECHING Basic knowledge on standard parts assembly 1.Installation of screws (3)Screw installation order (1) Installation of screws Mount the screws diagonally Correct Wrong in order of number orientation orientation 1 5 3 4 6 2 (2)Degree of screw tightening 2.Installation of snap ring...
Page 11
TECHING 3.Installation of Bearing (1)Install the bearing into the bearing seat hole (2)Install the bearing onto the shaft Correct orientation Wrong orientation Check the orifice of bearing block Check the shaft end for chamfer and for chamfer and burr; apply a little burr;...
Page 12
TECHING Important note: before assembly, find 1.2 Installation of ratchet pawl the bottled lubricating oil, be sure to put enough oil in all the places that need to be lubricated, otherwise the machine is easy to get stuck Position indicator for lubricating oil 1...
Page 13
TECHING 1.3 Installation of stop shaft 1.4 Installation of Support Shaft Total one place Tighten with a screwdriver Insert a screwdriver...
Page 14
TECHING 1.5 Installation of Support Board 1.6 Installation of ratchet pawl Total two places...
Page 15
TECHING 1.7 Installation of pulley assembly 1.8 Installation of swing arm Total one place Total two place Level The eyelet faces downward when this swing arm is placed horizontally.
Page 16
TECHING 1.10 Installation of ratchet Installation of swing arm Eyelet oriented to the right Total three places Bigger head faced down...
Page 17
TECHING 1.11 Installation of Shaft I and gear 1.12 Installation of Shaft II and gear Total four places The long end is the Total two places direction of the bull gear. Total two places Total two places...
Page 18
TECHING 1.14 Installation of rope pulley, rope pulley shaft and gear 1.13 Installation of rope pulley Total two places Total one places Wind the rope reversely and tightenen the rope end to prevent the knot from loosening.
Page 19
TECHING 1.15 Installation of bearing 1.16 Installation of ratchet pawl...
Page 20
TECHING 1.18 Installation of rope pulley 1.17 Installation of shaft II and gear...
Page 21
TECHING 1.19 Installation of shaft I and gear 1.20 Installation of pulley...
Page 22
TECHING 2 Assembly of front main board 2.2 Installation of front and rear main board 2.1 Installation of stop shaft Tighten with a screwdriver...
Page 23
TECHING 2.3 Installation of bearing 2.4 Installation of shaft cap...
Page 24
TECHING 3 Assembly of rope 2.3 Installation of clock dial 3.1 Installation of rope and pulley Step 2: Wind the rope from inside the pulley. 036-1 Step 3: Run the rope through the center hole of the drop hammer. Step 1: Wind the rope up...
Page 25
TECHING 3.2 Installation of rope in drop hammer cap 3.3 Assembly of drop hammer Wind the rope end reversely by one turn, and then tighten to prevent the knot from loosening. This is a X5 schematic view of winding of Point.
Page 26
TECHING 4 Assembly of pendulum 3.4 Installation of drop hammer 4.1 Installation of pendulum 036-3...
Page 27
TECHING 4.2 Installation of pendulum and swing arm...
Page 28
TECHING 5 Assembly of pointer Raise the drop hammer to the highest point, and align the tip of the pointer with the center mark, then tighten the pointer. ——...
Page 29
TECHING Hammer lifting method: Open the swing lever by the ring finger, and move the gear by the index finger clockwise to lift the hammer. Assembly completed...
Page 30
TECHING Troubleshooting 4-2 please check the swing space of the swing After assembly, if the motion is abnormal, please check arm axis is same as shown in figure or not. w h e t h e r t h e r e l e v a n t m o v i n g p a r t s a r e c o a t e d w i t h lubricating oil and the parts are missing or misplaced according to the instructions.
Page 31
TECHING 5>Please check whether the sling is wrapped correctly 7 > 6>Please check whether the rope is stuck. 6-1:Check if the rope is caught in the gaps at both Check whether the front and rear main boards ends of pulley (035) and...
Page 32
TECHING 8 > J u m p i n g t e e t h a p p e a r a n y w h e r e i n 8 > the process of swinging the pendulum h a m m e r t o t h e l o w e s t p o i n t . I t ’ s necessary to remove ratchet pawl 026, a n d s c r a p e p o i n t 8 >...
Page 33
TECHING Product Product Product name Qty. Product name Qty. picture picture Positioning disc Ratchet shaft 50-tooth gear Shaft II 22-tooth gear Shaft I 10-tooth gear Swing arm shaft 16-tooth gear Rope pulley cap Swing arm Ratchet shaft sleeve Shaft cap...
Page 34
TECHING Product Product Product name Qty. Product name Qty. picture picture Rope pulley Front main board sleeve 1.3 Ratchet pawl Rear main board Pawl shaft Support shaft Telescopic Bearing Ø13*Ø5*4 swing lever Cylindrical pin Pulley sleeve Ø2.5*10 Rope pulley Limiting shaft...
Page 35
TECHING Product Product Product name Qty. Product name Qty. picture picture Clock dial BearingØ7*Ø3*3 Pulley BearingØ6*Ø3*2.5 036-1 BearingØ9*Ø4*4 Drop hammer-1 Non-elastic rope Ø 036-2 Drop hammer-2 1.5MM*1.1M 036-3 Pointer Drop hammer-3 Screw CM2.0*4*4 BearingØ7*Ø4*2.5 Pendulum Screw CM3.0*8*6 ¢ 5.3/¢ 10X0.8...
Page 36
TECHING Product Product name Qty. picture E-shaped snap ring Ø7*Ø3*0.6 M2.0spring washer Screw CM3.0*16*6 Screwdriver...