Summary of Contents for Nitto Seiko SH300
- Page 1 Rotary auxiliary hopper SH300 Rotary Auxiliary Hopper SH300 Instruction Manual Assembly Machine Division NITTO SEIKO CO., LTD.
- Page 2 Rotary auxiliary hopper SH300...
- Page 3 The “SH300” is designed to be used basically combined with our “Vibratory Track Screw Feeder FF/FM503H” (hereinafter referred to as FF/FM503H). Note that the “SH300” is not a CE-mark qualified product. To purchase a CE-mark qualified product, please place an order specified “CE-mark qualified SH300-E”.
- Page 4 (SW1) and shut off the power to the product. And then contact our sales agent or your nearest sales office of Nitto Seiko Co., Ltd. for repair. If you continue using it without repair, a fire, electric shock or accident may occur.
-
Page 5: Table Of Contents
Rotary auxiliary hopper SH300 Contents Overview of “SH300” ............................1 What is “SH300”? ............................1 1.1. 1.2. Names of the parts ............................. 1 Use environment, installation, connection, and power-on ................2 2.1. Use environment ............................2 2.2. Installation ..............................2 2.3. -
Page 6: Overview Of "Sh300
Rotary auxiliary hopper SH300 1. Overview of “SH300” 1.1. What is “SH300”? “SH300” is a device, which is installed to the Vibratory Track Screw Feeder “FF/FM503H”, to fill screws into the basket of the feeder automatically. 1.2. Names of the parts (1) Hopper Screws are put in it. -
Page 7: Use Environment, Installation, Connection, And Power-On
(1) Catch the basket at the rear of the main unit of “FF/FM503H” with the left and right hooks of the “SH300”. (2) Insert the pole with a rubber foot into the “SH300” main unit so that the hopper does not fall down even when the screws are put in. -
Page 8: Connection
(1) Check that the illuminated power switch (SW1) of the “SH300” is turned off. (2) Connect the plug of the “Power cable with a plug” of the “SH300” to the 3P receptacle (CN SH) of the Vibratory Track Screw Feeder “FF/FM503H”. (Refer to the “Vibratory Track Screw Feeder... -
Page 9: Guarantee
Rotary auxiliary hopper SH300 4. Guarantee We guarantee as described in the warranty below if the product you have purchased fails. Note that the product that failed outside Japan is to be repaired by your nearest sales agent. 4.1. Warrantee We repair the components of this product free of charge if judged as defective and if the defects are caused by or attributable to a problem with materials or our production. -
Page 10: Appendix
In principle, attach a noise filter etc. to the input part of the stabilized power source used. The cable, when it is provided by the customer, connected to the “SH300” must be as short as possible while it should be placed properly so that the cable will not be influenced by the cables connected to other equipment or machines. -
Page 11: External Dimensional Drawing
Rotary auxiliary hopper SH300 5.2. External dimensional drawing... -
Page 12: Parts List
Rotary auxiliary hopper SH300 5.3. Parts list Free bare: Kyoei Seiko: C-5S Hexagon socket head screw (6 5) Hexagon socket head screw (6 15) Spacer Mac Eight: EP-6 2-Machine screws (Pan-head) Free bare Proximity sensor Kyoei Seiko: C-5H... - Page 13 Silicon agent: Shin-Etsu Chemical Co., Ltd.: KE45T Proper amount Proximity sensor: SUNX Limited: GXL-15F Stepping motor: Sanryusha Co., Ltd.: P43EAG4140-60(24)6 Parts-mounted board: NITTO SEIKO Co., Ltd.: SH300-SM LED illuminated rocker switch: Nihon Kaiheiki Industry Co., Ltd.: JW-S11RKKM Fuse holder: SATO PARTS CO., LTD.: F-400-01A2 5 ×...
-
Page 14: Electric Circuit Diagram
Rotary auxiliary hopper SH300 5.4. Electric circuit diagram... - Page 15 Rotary auxiliary hopper SH300 MEMO...
- Page 16 Rotary auxiliary hopper SH300 Rotary Auxiliary Hopper SH300 Instruction Manual (Ver. 2.0) Prepared on: September 10, 2007 NITTO SEIKO CO., LTD. Assembly Machine Division http://www.nittoseiko.co.jp/ Assembly Machine Shiroyama-cho 2, Ayabe, Kyoto 623-0003, Japan Division: Telephone: (0773) 43-1550 Facsimile: (0773) 43-1554...