Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for FOS Technologies 192Ch DMX Console
- Page 1 FOS 192Ch DMX Console...
-
Page 2: Product Specifications
PRODUCT SPECIFICATIONS TECHNICAL SPECIFICATION Voltage: 100 / 240 Volt AC, 50 / 60 Hz, to 12V DC, 0.5A. (Supplied Power Supply.) Control: 192 DMX Channels total: 12 fixtures with a max of 16 Channels each. Programming abilities: 30 banks with 8 scenes each and 6 chases with capacity of 240 scenes each. Midi: Supports midi input for scene &... - Page 3 PROTECTION AGAINST SOLIDS AND WATER Only for IP-rated fixtures The protection level of a housing is set by applied standards. For classification there is used the IP-Code. It contains the declaration „IP“and two following numbers. The first number characterizes the protection against harmful effects of solids, the second is rating the water protection.
- Page 4 Warning NOTE! If the signal cable is over 60 m between the DMX512 controller and fixture or between two fixtures, then a DMX signal amplifier is needed as well. Also, always terminate the DMX line (s) with a 120 Ohm resistor. Console Layout Description Scanner Buttons: To control independently your fixtures, you should arrange them in to the 12...
- Page 5 33 to 48 49 to 64 65 to 80 81 to 96 97 to 112 113 to 128 129 to 144 145 to 160 161 to 176 177 to 192 SCENE buttons: in these buttons, you can save and recall a scene (single step). CHANNEL sliders: adjust the intensity of the DMX channels, from zero to 255.
-
Page 6: Programming Mode
Auto / Del: Activates or deactivates the Auto run mode & deletes steps, banks & chases. Music / Bank Copy: Activates or deactivates the Music mode & copies a bank in to a chase. Tapsync / Display: In Auto run, sets the speed of banks / chases run (by tapping it with your desired rhythm) and changes the channel value type on the screen (in percentage 0 to 100% or in DMX value, 0 to 255). - Page 7 Do the same with all the fixtures you want to include in the scene. • • Select the desired Bank with the Up and Down buttons. • While holding down the Add/Midi button, press one of the Scene buttons to store your created step.
- Page 8 Use Bank Up & Down buttons to choose the bank you wish to copy. • • Press Add / Midi button. Select another Bank, in which you wish to copy using the Up & Down buttons. • Press Music / Bank Copy button. All the LEDs will flicker, indicating that your bank is copied. •...
-
Page 9: Run Scenes
Delete a step in a chase • Select the Chase which includes the step you wish to delete. The LED display will show up the current chase, step and bank. • Press Tap Sync / Display button. The LED display will show the current chase and step. Use the Bank Up &... - Page 10 Music Run mode • Press the Music / Bank Copy button, until the corresponding LED illuminates. Use the Bank Up & Down buttons to select the desired bank, which will start run the scenes to • the rhythm of the music. Pressing again the Music / Bank Copy button, will deactivate the Music mode.
-
Page 11: General Information
Bank 1 Turn On / Off Scene 3 Turn On / Off Scene 4 Turn On / Off Scene 5 Turn On / Off Scene 6 Turn On / Off Scene 7 Turn On / Off Scene 8 Bank 2 Turn On / Off Scene 1 Turn On / Off Scene 2 Turn On / Off Scene 3... - Page 12 Always disconnect the fixture from main power before replacing a fuse. Use only the appropriate fuse, with the same type and rating. A fuse with different rating, can damage the fixture in case of failure. Risk of electric shock and / or fire: The fixture must be earthed, supplied always with its nominal voltage and cleaned periodically from dust.
Need help?
Do you have a question about the 192Ch DMX Console and is the answer not in the manual?
Questions and answers