SUNFLEX SWISH ELEMENTS BAY KIT Fitting Instructions

Fitting the Bay Corner Fitting the Bay Corner
1. Adjust the bay corner into the desired angle by loosening the 1. Adjust the bay corner into the desired angle by loosening the
segment screw. Once in the desired positon re-secure the segment screws. Once in the desired positon re-secure the
screw. ( g.15) screws. ( g.15)
2. Slide the poles onto the plastic bung ends of the bay corners.
( g.16)
Bay corners should always be supported by two pass over
brackets.
Preparing the curtain
( g.17)
1. Leave the solid rings aside, slide the pass over rings and 1
90˚
solid rings onto the pole, approximately 1 ring per 100mm of 45˚
180˚
pole, ensuring that 1 solid ring goes on last.
2. When using a centre bracket an equal number of rings will
need to be used either side of the bracket.
Fixing the pole
( g. 18)
1. Loosen the grub screw on the bracket.
2. Place pole in bracket.
3. Tighten the grub screw until the pole does not slide in the
bracket.
Fixing the fi nial Fixing the collar
( g.19) ( g.19)
1. Place one of the full rings on the pole after the bracket. 1. Position one solid ring between the bracket and the collar.
2. Slide the nial onto the pole and tighten the grub screw until 2. Push the collar onto the end of the pole.
3. Tighten the grub screw on the collar. the nial is secure.
For Stud fi nials ( g.20)
Z
Fixing the fi nial
1. Place one of the full rings on the pole after the bracket.
2. Push the nial onto the pole until it is secure. 1. If the collar is already installed on the pole, unscrew the grub
screw and remove the collar. We do not recommend installing
the nial while the collar is tted as it could scratch the pole.
( g.20)
2. Screw the nial on the cup end of the collar. Please note that
Installing the curtain
different design are available through the range. ( g.21)
1. Equally space curtain hooks along curtain header, you will
3. Push the nial onto the end of the pole. ( g.22)
require one hook for every ring. ( g.21)
4. Tighten the grub screw on the collar.
2. Place hooks through the eyelet on the ring. ( g.21)
3. Test the installation by drawing the curtains across the pole.
Installing the curtain
( g.22)
1. Equally space curtain hooks along curtain header, you will
require one hook for every ring. ( g.23)
2. Place hooks through the eyelet on the ring. ( g.23)
3. Test the installation by drawing the curtains across the pole.
( g.24)
Sunfl ex , Keys Park Road, Hednesford, Cannock, WS12 2FR Sunfl ex, Keys Park Road, Hednesford, Cannock, WS12 2FR
• tel: +44 (0)330 005 2233 • tel: +44 (0)330 005 2233
• email: enquiries@sunfl ex.co.uk • email: enquiries@sunfl ex.co.uk
90˚
Distance between bracket centers
90˚
180˚
d1
Distance between bracket centers
15
Length of end pole = d1 +
147.5mm
16
17
Distance between bracket centers
d1
Distance between bracket centers
Length of end pole = d1 +
6
147.5mm
18
2
W 4
3
W
19 19
Z
1
MIN 10mm gap
3
6
20
20
2
5
1
22
d1
21
d1
Approx.
23
22
10cm
Approx.
24
10cm
• fax: +44(0) 1543 279505 • fax: +44(0) 1543 279505
• web: www.sunfl ex.co.uk • web: www.sunfl ex.co.uk
SWISH DESIGN STUDIO BAY KIT
45˚
45˚
180˚
Please read these instructions carefully and check the contents of the pack before attempting to
W
1 3 6 2
Pack Content
3
Z
Z
{
MIN 10mm gap
Z
5 7 OR
Z
stud drawing.AI 3 01/04/2014 09:19:22
MIN 10mm gap
Parts
1 Pole
1 Corner Joint
2 Bracket
2 End Brackets
3 Pass Over Bracket
3 Passing Brackets
4 Standard Collar
4 Pass Over Rings
5 Solid Ring
5 Solid Rings
6 Pass Over Ring
7 Joiner
6 Pole
21
8 Bay Corner
7 Finial
d2 (distance between end brackets)
Should any component be missing, please call the Customer Care Department on
d2 (distance between end brackets)
DO NOT over reach. Always move the Step Ladder so that you are in a safe working position.
Take care when using power tools, use of a Residual Current Device (RCD) is recommended.
Always use eye protection when drilling. Beware of hidden pipe runs and cables.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled product. d1+d2+d1=Pole Length
PLEASE KEEP OUT OF THE REACH OF YOUNG CHILDREN. SMALL PARTS - CHOKING HAZARD
PLEASE KEEP THESE INSTRUCTIONS AND THE BATCH CODE ON THE PACKAGING FOR FUTURE
d1+d2+d1=Pole Length
SWISH ELEMENTS BAY KIT
Fitting Instructions
Please keep for future reference
Tools required
assemble and x this product.
W
3 1
2 6
W
4 5 2 W 5 1 8 3 3
3
5
Bay Length
Bay Length
300cm 400cm 500cm
400cm
4 4 4
2
3 3 2
3
4 4 4
4
2 2 2
36
4 4 4
4
26 36 46
1 1 1
3
2 2 2
2
0330 005 2233.
Safety Recommendation
Only use a Step Ladder to install this product.
DO NOT hold or lean on the pole to support your weight.
We recommend you use two people for installation of larger poles.
REFERENCE IN CASE OF ANY QUERIES
1
6
7
2
2
1
8
4
3
3
3
1
6
1
3
6
5
2
2
5
5
4
1
d1
d1
Approx.
10cm
Approx.
10cm
6139L/ISS1 6454L/ISS2