IBOS CamBoss Original Operating Instructions
  1. Manuals
  2. Brands
  3. IBOS Manuals
  4. Digital Camera
  5. CamBoss
  6. Original operating instructions

IBOS CamBoss Original Operating Instructions

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
CamBoss
;
Original operating instructions
revision 1.3 02/2020
Instructions for the safe and economic operation of CamBoss monitoring system and
its maintenance to ensure trouble-free operation. All trademarks mentioned in this
document are the property of their respective owners.
Equipment manufacturer:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CamBoss and is the answer not in the manual?

Questions and answers

Summary of Contents for IBOS CamBoss

  • Page 1 CamBoss Original operating instructions revision 1.3 02/2020 Instructions for the safe and economic operation of CamBoss monitoring system and its maintenance to ensure trouble-free operation. All trademarks mentioned in this document are the property of their respective owners. Equipment manufacturer:...

  • Page 2: Table Of Contents

    70 dB. The EC declaration of conformity is part of this manual. 3. General description of machinery: The CamBoss inspection system is used for inspections of sewerages and piping. The system consists of the following main components: 1 / 19...
  • Page 3 CamBoss CamBoss flow chart 2 / 19...
  • Page 4 The maximum speed of the trolley is 20 m/min. MAXON brushless motors are intended for harsh working conditions. The CamBoss trolley is equipped with a rear-view camera with its own illumination source, which enables to view the cable's behaviour when reversing.

  • Page 5: Description Of Operator Positions

    5. Intended usage and presumed usage of the system The CamBoss monitoring system is intended solely for inspection of pipes of all kinds. Other use or use beyond this limitation is not considered to be an intended use. Never use the CamBoss sewerage and inspection system for any other purpose.

  • Page 6: Commissioning And Usage Instructions

    CamBoss 7. Commissioning and usage instructions On request, the manufacturer will carry out training of operating personnel. The operating personnel must have the knowledge of at least within the scope of this operating manual. Check the following before putting the device in operation: 1.

  • Page 7: Conditions Under Which The Device Meets Requirements For Stability

    This is done by specially designed “rollers”. The cable protection accessory are available from IBOS a.s. If you do not have such a device, you must ensure such protection in another way. This will significantly reduce the risk of cable damage and increase its service life.
  • Page 8 10. Safety instructions Read the following safety precautions carefully and observe them. They are intended for your own safety, your employees, as well as for preventing damage to the CamBoss system and its components. Ensure that no liquid can enter the control unit, control panel or cable drum...
  • Page 9 CamBoss Danger of injury due to contact with hot parts of the system! When working with the system, be aware that individual components (especially lighting, cameras and trolleys) can be very hot during operation. Explosion hazard! Never use this device in piping that contains explosive atmospheres. For this purpose, only specially manufactured equipment, which is marked in appendix, is approved.
  • Page 10 CamBoss camera seals and increases its wear. The pressure over 1 bar is already critical and sealing of the device can be compromised. Caution! The operator of the plant is responsible for the proper disposal of the waste! 11. Controlling the system All necessary controls are located on the control unit panel.
  • Page 11 The probe signal detector is available from IBOS a.s. Distance travelled indication The CamBoss is provided with an odometer indicating the travelled distance (cable unwound), which is located on the winch cable. The measured value is displayed on the display of the control panel.

  • Page 12: Centring Elements

    CamBoss Inspection reports, inspection records Use the software installed on the computer of the control unit to create a video recording and a log. To document the recorded damaged locations, you may view the corresponding measured data on the current video image and use the keypad to enter additional comments.

  • Page 13: System Maintenance

    Try to correct the cause of the fault using the information provided herein below. If the cause remains unclear or the suggestions for correction do not lead to successful correction of problem, please contact IBOS a.s. customer service. 12 / 19...
  • Page 14 Poor contact in the camera Check the secure connection connector. connector connection. Image disturbances Replace the camera cable Broken cable wire. or call IBOS a.s. service. Dirty windshield. Clean the windshield. Incorrect image Scratched windshield. Replace the windshield. Service to remove the No AC power.

  • Page 15: Cleaning

    Replacement of windshield of the camera If the operating personnel have sufficient training, the damaged glass may be replaced, otherwise contact the IBOS a.s. service centre for technical support. To replace the camera windshield: • Unscrew the front camera cover;...
  • Page 16  Execute the checklist instructions for system maintenance;  Regularly inspect the personnel to ensure that they are aware of safety and risks. Prevention of material damage As the operator of the CamBoss inspection system, you are responsible for the observance of the following points: ...
  • Page 17 1 x cable winch / push camera Interface 1 x power supply 110 – 240 V AC 1 x RJ45 (Internet) CamBoss trolley and cameras control unit, two joysticks, micro-buttons, Control panel alphanumeric keyboard 3.5 (110 V AC, 60 Hz) Current draw [A] 1.7 (230 V AC, 50 Hz –...
  • Page 18 CamBoss Rotary camera head KZ60 ¼" CCD image sensor, automatic white level stabilization, 317,612 pixel / 400 horizontal TV lines, LED illumination, swivelling 115° to both sides, 68° angle of view, “slip-ring” connector, pressure sensor, optional centring with accessories Luminance sensitivity...
  • Page 19 The liability we accept under the above conditions, is limited solely to repairs, compensation or refunds. IBOS a.s. shall not be liable for any consequential or incidental damages which may arise in connection with the sale or operation of the product. This also applies to consequential damages that can be classified as commercial losses, for example loss of profits, downtimes, damage to reputation, and damage to other instruments or assets.
  • Page 20 CamBoss We wish you every success and joy in working with your new CamBoss TV inspection system. We are happy to answer any questions you have. We will be grateful for the suggestions for improvement and other feedback! IBOS a.s.

Table of Contents