Summary of Contents for Panther 55-0030
- Page 1 55-0030 SWIM PLATFORM BRACKET FOR LIGHT WEIGHT AUXILIARY ENGINES UP TO 20 HP INSTRUCTION MANUAL REV. 01/17 1.604.940.2010 | sales@cmpgroup.net...
- Page 2 Auxiliary Outboard Motor Bracket Mounting Instructions for Proper Location of Outboard Motor AUXILIARY OUTBOARD MOTOR BRACKET CAUTION GUIDELINES 1. Always remove your motor from bracket when trail- ering. Failure to do so may result in damage to boat, mo- tor, or bracket. 2.
- Page 3 ���������� ��� ���� ������� ������� ������� 1. Set the bracket in the desired moun�ng loca�on. A. Check the area underneath for clearance for moun�ng bolts, fender washers and nuts. A minimum of four 1/2” Stainless Steel bolts must be used to mount the Panther bracket to the swim pla�orm, u�li�ing pre‐drilled holes in the moun�ng plate. B. �he moun�ng bolts should be posi�oned as far apart as possible with fender washers on the under side to assure adequate support. C. On swim pla�orms which are not molded directly onto the boat hull you must use the support tube assembly. On these applica�ons, make sure you have clearance and a moun�ng loca�on for the support tube bracket to be a�ached to the transom before drilling and moun�ng the Panther bracket. 2. Bolt the side brackets to the motor board. A. Use the widest bolt holes to mount the side brackets. (See picture #1). ...
- Page 4 3. Select moun�ng loca�on to secure the side brackets/motor board to the main brac A. �here are three height se�ngs for the motor board. Select the best se�n 3. Select mounting location to secure the side brackets/motor board to the main bracket. outboard will not cavitate when in opera�on.. (See Moun�ng Instruc�ons �oca�on of �utboard Motor). A. There are three height settings for the motor board. Select the best setting to assure the outboard will not cavitate when in operation..
- Page 5 H. Divide the support tube length needed in half and drill a hole through both support tubes, using a 5/16” drill bit. I. Use the 5/16‐18 x 1‐1/2 Cap Screw and a 5/16‐18 nylon insert nut through the hole H. Divide the support tube length needed in half and drill a hole through both support drilled in step F to keep the adjustment of the support tubes in one posi�on. �See tubes, using a 5/16” drill bit. picture #6) I. Use the 5/16‐18 x 1‐1/2 Cap Screw and a 5/16‐18 nylon insert nut through the hole drilled in step F to keep the adjustment of the support tubes in one posi�on. �See picture #6) Picture #3 Picture #4 Picture #3 Picture #4 Picture #5 Picture #6 Picture #3 Picture #4 Picture #5 Picture #6 Picture #5 Picture #6 ...
- Page 6 �������� ��� ���� ������� ��������� �������� ���������� ���������� ���� 1/4‐20 X 3/4" Cap Screw Tube Support Bracket to Base Plate 2 1/4‐20 Nylon Insert Nut Tube Support Bracket to Base Plate 2 1/4" Flat Washer Tube Support Bracket to Base Plate 2 5/16‐18 x 1‐3/4" Cap Screw Support Tube to Support Tube Bracket 2 5/16‐18 x 1‐1/2" Cap Screw Outer Support Tube to Inner Support Tube 1 5/16‐18 x 1" Cap Screw Angle Plates to Base 6 5/16‐18 Nylon Insert Nut All 5/16" Cap Screws 13 5/16" Flat Washer Angle Plates to Base Plate 20 5/16" x 2‐1/2" Carriage Bolt Plas�c �otor Board to Angle Plates (Lower) 2 5/16"x 2‐1/2" Fanged Elevator Bolt ...
- Page 7 SERVICE AND WARRANTY Should your unit ever require service, please do not return the product to your dealer. Please call the number below for special instructions on shipping and handling. Please call between 9:00 am - 5:00 pm (Pacific Time) Monday through Friday.
Need help?
Do you have a question about the 55-0030 and is the answer not in the manual?
Questions and answers