Advertisement
Quick Links
Advertisement
Related Manuals for Logosol SAUNO
Summary of Contents for Logosol SAUNO
- Page 1 USER MANUAL Ref. no: 0458-395-0641 SAUNO DRYING CHAMBER...
- Page 2 Logosol has been manufacturing sawmills since 1989. In that time we have supplied approximately 50,000 machines to satisfied customers the world over.
- Page 3 TABLE OF CONTENTS Safety instructions Components: Drying chamber Assembly Sauno drying programme CE Declaration of conformity...
- Page 4 SAFETY INSTRUCTIONS SITING For your own safety, do not start assemble or use the drying chamber without first having read and Risk of personal injury understood all the contents of this user manual. Do not let persons who have not read the Risk that the stack of wood falls on someone.
- Page 5 • Only use original parts supplied and approved by • the labelling of the drying unit matches your electrical Logosol for the purpose. Use only purpose made connection. original parts from Logosol. After service, the drying unit has to be restored to its original design.
- Page 6 6200-000-0020 9031-011-0020 03-02500 03-02390 03-02391 03-02389 03-02465 03-02500 03-02468 14 x 03-02470 14 x 03-02469 14 x M8x20 12 x 03-02467 M6 x 45 03-02466 4,2 x 14 16 x 4,2 x 25...
- Page 7 SAUNO DRYING CHAMBER BOLTS & NUTS Definition of fasteners. Allen bolt Shoulder bolt Phillips bolt Partial thread Allen bolt Hex bolt Slotted bolt Set screw Partial thread hex bolt Hex nut Flange bolt Flange nut Partial thread flange bolt Carriage bolt...
- Page 8 6200-000-0020 03-02389 03-02390 M8x 20 03-02465 03-02391 M8x 20 03-02466...
- Page 9 SAUNO DRYING CHAMBER 6200-000-0020 M6x 45 M6x 45...
- Page 10 6200-000-0020 Mount the laths on the top struts. These laths are mounted from the inside of the drying tent and are folded by hand around the struts. Start from one side side of the drying tent and place the laths with about 25 cm spacing between them.
- Page 11 SAUNO DRYING CHAMBER 6200-000-0020 Use a pair of scissors and cut a hole in the outer tent to enable the installation of the drying unit. Fold the corners around the inside of the hole in the tent side plate. Fit the drying unit and safety plate in the cut hole in side of the tent.
- Page 12 6200-000-0020 Take a board that is 50 mm x 100 mm and cut four pieces that are 670 mm in length. Fit these boards to the feets for the lower struts. 4.2 x 25 03-02500 9031-011-0020 Use the tent side plate with the ventilation hole as a template when you make the hole for the air vent.
- Page 13 SAUNO DRYING CHAMBER 6200-000-0020...
- Page 14 High temperatures force out resin from the wood, which reduces the risk of later resin bleeding. The colour changes that occur in a Sauno wood drying kiln are usually minor. If you are unsure of what colour changes there will be, it can be a good idea that you first dry a smaller amount of wood as a test.
- Page 15 DRYING TECHNIQUE The Logosol WDU kiln uses a relatively low temperature but with high circulation, which gives an energy efficient process. The low temperature used will also give minor colour changes to the wood and reduces the occurrence of sap and resin bleeding.
- Page 16 LOGOSOL AB, Fiskaregatan 2 S-871 33 Härnösand, Sweden Phone: +46 611 182 85, herewith declares that the Sauno Drying Chamber has been manufactured in conformity with: Machinery Directive 2006/42/EG, EMC Directive 2004/108/EG and LVD Directive 2006/95/EG. Mattias Byström, Product Manager, is responsible for the technical files.