Advertisement
2. INTRODUCTION
Mobile workshop extractors suitable for attachment to most
static workshop machines including bandsaws, table saws,
scroll saws, planers and sanders. Supplied with 2m of
Ø100mm suction ducting.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . SM46.V3
Airflow: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500cfm
Impeller Diameter: . . . . . . . . . . . . . . . . . . . . Ø230mm
Intake Diameter: . . . . . . . . . . . . . . . . . . . . . . Ø100mm
Flex Hose Diameter:. . . . . . . . . . . . . . . . . . . Ø100mm
Flex Hose Length: . . . . . . . . . . . . . . . . . . . . . . . . . 2m
Motor Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . 750W
Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V
Nett Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . 24.5kg
4. ASSEMBLY
NOTE: Numbers in brackets are the item numbers on the parts diagram and in the parts list.
4.1.
Attach the four castors (1) to the underside of the base (4) using screws (2), washers (3 & 29) and nuts (30). Support base (4) on
battens, or similar, raising castors clear of floor to give stability for the following assembly tasks.
4.2.
With screws (14) and washers (12) attach column (20) to base plate (4).
4.3.
Attach motor (18) to column (20), so that collector body is positioned as shown in parts diagram, with screws (14) and washers (12).
4.4.
Install collector (23) to collector body (11) using packing (22) and flange head screws (15). Ensure collector is directly over base.
4.5.
Attach collector support rods (31) to base with screws (15), M5 washers and nuts, and to collector with screws (2), washers (29) and
nuts (30).
4.6.
Attach filter bag support (35) to collector with screws (34).
4.7.
Fit upper (filter) bag (25) over upper bag flange on collector (23) and secure by tightening built-in strap. Hook loop on end of bag (25)
over support arm (35). Fit second (collector) bag (24) to lower bag flange on collector.
NOTE: Bag clamps (36) are provided and may be used for additional bag security.
4.8.
Adjust screw (fig.1A) to bear lightly against the side of the collector body (fig.1B) and lock by tightening nut (fig.1C).
5. OPERATION
WARNING! Before operating the extractor ensure that you read,
‰
understand and apply the safety instructions in Section 1.
5.1.
Confirm that supply voltage matches the voltage shown on the motor
data plate and that the motor switch (16) is 'Off'.
5.2.
Connect extractor hose to the inlet (6) on the collector body (11) and
attach other end to extractor point on equipment.
WARNING! DO NOT operate extractor without the hose attached.
‰
5.3.
Plug into mains supply and press motor switch 'On'.
5.4.
Ensure that the lower bag is emptied of dust and chips on a regular
basis and is not allowed to become full.
NOTE: Fitting a reducer to the extraction hose will reduce the volume
of dust extracted.
WARNING! This unit is not suitable to be used to extract dust via a
‰
piped system.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
01284 703534
sales@sealey.co.uk
Original Language Version
QTY
CONTENTS
1
Collector body with motor
1
Seal
1
Base Plate
1
Inlet Hose (2m)
3
Support Rod
1
Collector
1
Column
1 bag
Screws, nuts, washers
2
Filter / Collector Bag
4
Castors
Unpack the extractor components and check that all
are present and undamaged. In case of shortage or
damage please contact the supplier.
fig.1
SM46.V3 | Issue 7 (2,3) 27/02/2019
www.sealey.co.uk
Advertisement
