Summary of Contents for Smart+ Products SPP155BDSS
- Page 1 Beer Dispenser SPP155BDSS Instruction Manual For Household Use Only. Read These Instruction before Using This Unit Save These Instructions.
-
Page 2: Safety Precautions
Safety Precautions Read all of the instructions before using this appliance. When using this appliance, always exercise basic safety precautions, including the following: Use this appliance only for its intended purpose as described in this operation manual. This appliance must be properly installed in accordance with the installation instructions before it is used. See the installation section for more details. - Page 3 Important Safety Precautions of CO2 (Carbon Dioxide) Gas CO2 gas can be dangerous! CO2 cylinders contain high-pressure compressed gas, which can be hazardous if not handled properly. Make sure you read and understand all the procedures for the CO2 cylinders before installation.
-
Page 4: Proper Location
SAVE THESE INSTRUCTIONS For Future Use DANGER! Risk of child entrapment! Before throwing away your old appliance: ● Take off the doors. ● Leave the shelves or other accessories in place so that children may not easily become trapped inside. (Note: If the refrigerator has been placed in a horizontal or tilted position for any period of time, please wait at least 24 hours before plugging the unit in.) Proper Location... -
Page 5: Installing The Casters
Assembly Instructions Read assembly instructions carefully to ensure that you understand all installation instructions before installing the Beer Dispenser. If after completing the process you are still unsure whether the Beer Dispenser has been properly installed, we recommend that you contact a qualified installer. Note: Allow the Beer Dispenser to stand in an upright position for at least 8 hours before plugging in the unit. -
Page 6: Installing The Guardrail
Installing the Guardrail Follow these steps below to install the guardrail. Place the guardrail on top of the cabinet. Align all support feet of the guardrail with the holes of on the top of the unit. Installing the CO2 Regulator Shut-Off and the CO2 Cylinder Connect to... - Page 7 Tapping the Beer Keg – Installing Keg Tap (Single-Valve Type Barrel) Follow these steps below to tap the beer keg. Make sure the black pull handle of the tap is in the closed (up) position before installing it on the keg (Fig.
-
Page 8: Operating Your Beer Dispenser
Operating Your Beer Dispenser Dispensing Beer Follow the steps below to dispense beer. Make sure that the Beer Dispenser is plugged in properly to a 120V, 60Hz, 15Amps grounded AC power outlet. Place the drip tray under the beer faucet to avoid messes from excess beer. Open the beer faucet by pulling the tap towards you to dispense the beer. -
Page 9: Special Safety Information
SPECIAL SAFETY INFORMATION Important Safety Message for Draft Beer Dispensing Your Beer Dispenser system has two safety devices already provided in the CO2 pressure line. The coupler for this Beer Dispenser is compatible with the ¼ Pony Keg sized barrel and the ½ Barrel full size (US Kegs). - Page 10 CO2 Bottle Regulator Large Butterfly Nut Secures Hose to Beer Tap Beer Tap Shown connected to Regulator Hose #1 by Hose Connecting Beer Tap to Regulator & CO2 Bottle Illustration E Hose #1 Connecting Beer Tap to Regulator & CO2 Bottle Hose #2 Connects Dispenser Assembly to Beer Tap...
- Page 11 QUICK ASSEMBLY INSTRUCTIONS Installing Casters 1. Remove all items from inside cabinet. 2. Lay Beer Dispenser on its side. 3. Install four casters, making sure the two locking casters are up front 4. Stand Beer Dispenser up on casters and allow Freon to settle for at least 8 hours before plugging *All O-rings and rubber washers are preinstalled by the factory, but should be double checked.
Need help?
Do you have a question about the SPP155BDSS and is the answer not in the manual?
Questions and answers