Pro-Line II 8200 Operating Instructions

8200 FAUTEUIL PRéSIDENT à HAUT DOSSIER EN CUIR
7
11R
9
12
DESSIN DéTAILLé A:
Avec le coussin du dossier (7) sur une
surface plate, attacher les supports du
dossier (12) au coussin du siège (6).
8
6
4
12
13
3
7
12
8,10
Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués sur la liste et
s'assurer que les quantités des pièces reçues sont correctes.
éTAPE 1 Insérer les cinq roulettes (2) dans la base (1) et pousser fort jusqu'à ce que chaque roulette (2) s'encliquette. Insérer le vérin
pneumatique (3) dans la base (1), et glisser le soufflet (4) sur l'arbre du vérin pneumatique (3).
éTAPE 2 Attacher la plaque du siège (5) au coussin du siège (6) avec la flèche orientée vers l'avant du fauteuil en utilisant quatre vis
(8). RESSERRER COMPLÈTEMENT LES QUATRE VIS.
éTAPE 3 Placer le coussin du dossier (7) sur une surface plate et aligner les supports du dossier (12) sur le coussin du siège
(6). Attacher les supports du dossier (12) au coussin du siège (6) en utilisant quatre rondelles plates (10) et quatre vis (8) COMME
MONTRé DANS LE DESSIN DéTAILLé A.
éTAPE 4 Attacher les bras (11L et 11R) au coussin du dossier (7) et au coussin du siège (6) en utilisant deux vis de bras (9) pour
chaque bras RESSERRER COMPLÈTEMENT TOUTES LES VIS.
éTAPE 6 Placer le siège assemblé sur le dessus du vérin pneumatique (3) et pousser la pression vers le bas.
ATTENTION : VéRIFIER QUE TOUS LES VIS SONT INSTALLéS ET BIEN SERRéS AVANT DE L'UTILISER.
INSTRUCTIONS DE MONTAGE
11L
9
12
8,10
8,10
6
5
8
PIÈCE
1. Base . . . . . . . . . . . . . . . . . . . . . 1
2. Roulettes . . . . . . . . . . . . . . . . . 5
3. Vérin pneumatique . . . . . . . . . . 1
8
4. Soufflet . . . . . . . . . . . . . . . . . . . 1
5. Plaque du siège . . . . . . . . . . . . . 1
6. Coussin du siège . . . . . . . . . . . . 1
7. Coussin du dossier . . . . . . . . . . 1
8. Vis . . . . . . . . . . . . . . . . . . . . . . . 8
9. Vis de bras . . . . . . . . . . . . . . . . . 4
10. Rondelles plates . . . . . . . . . . . 4
11.
Bras gauche (11L) et droit (11R)
1 12. Support du dossier préinstallé . 2
2
13. Allen Wrenches (not shown) . . 2
QTé
1
. 2
WARRANTY
Pro-Line II chairs are warranted* from the date of purchase against failure due to material and workmanship as follows:
• Lifetime on component parts including pneumatic cylinder, control mechanism, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
• We can not warrant leather against routine scratching and scuffing, as all leather is subject to minor blemishes in normal use.
To make a warranty claim, contact Parts Department. Provide model number and description of the problem and obtain return authorization.
At it's option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer's component. The customer must prepay freight on any components returned to the factory.
Return freight on components still in warranty will be paid by Office Star Products.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs. or
less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other
event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a five
year warranty on all parts applies. Fabric and foam is warranted for one year.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
All Proline II chairs are built to meet or exceed ANSI BIFMA standards.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts
are damaged or missing. Our Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail
parts@officestar.net, by Fax 1-909-930-5629, or toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00
p.m. Pacific Time.
© Office Star Products Avril 2006
8200 EXECUTIVE LEATHER HIGH BACK CHAIR
OPERATING INSTRUCTIONS
FEATURE
• HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever
(1). To lower seat height sit on chair and lift lever (1).
NOTE: It is normal for chair to slightly lower under body
weight.
• LOCKING TILT ADJUSTMENT
For individual comfort, this chair has been equipped
with an adjustment that will allow the user to change
the tension of the tilting feature. Turn knob (2)
clockwise to increase tension and counter-clockwise
to decrease or ease the tension. To lock return chair
to the upright position and push lever (1) in. To unlock
pull lever (1) out.
NOTE: Be careful not to loosen back tilt adjustment
knob completely.
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and
knobs are securely tightened.
2
3. Check that all bolts screws and knobs are tight every
three months or as needed.
4. Do not overturn back tilt knob when decreasing
tension.
5. Dispose of packing material properly. Do not
use plastic cover as head covering. It may cause
suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.
P.O. Box 3520. • Ontario, CA 91761 • www.officestar.net • parts@officestar.net