Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Ather Dot
- Page 1 Home Charging Point...
- Page 2 USER MANUAL & GUIDE Manuals might be boring, but do flip through every page. We have cut the faff to keep this manual to the point, so that it’s easy to read.
- Page 3 What’s in the box? Specifications Installation Pre-checks How to install? Connecting the Ather Dot™ to your meter Safety instructions How to take care of the Ather Dot™ ? The PRCD The Dos & Don’ts Cleaning Learn its language Other safety instructions Warnings!
- Page 4 All about the Charger 6A Three Pin Plug Ather Dot ™ Ather Dot™ is a home charging point for your Ather 450. The step-by-step installation process has been jotted down clearly here, along with the dos & don’ts, warnings and cautions.
- Page 5 Installation Input Operating voltage and wiring We have detailed out every 185V AC - 275V AC single-phase step here to ensure a smooth installation. Pre-checks are a Frequency must, so flip the page and go 50 Hz through each one of them. Current 3.5A maximum Output...
- Page 6 Ensure that the electric source is close by. The Ather Dot™ comes with 1 meter of input cable. The open terminals of the input cable must be connected to the circuit breaker that is next to the utility energy meter of your home, as explained in the “How to install?”...
- Page 7 Step 2 Step 5 Clear any clutter around the Ather Dot™ Detach the wire that’s connecting the face -100mm on the docking side for an easy and the body to separate them. access to the charging connector. Step 3 Drill holes with an M6 drill attachment and install the wall inserts in the drilled holes.
- Page 8 Step 7 Step 9 Make sure the charging wire passes from Take the face of the Ather Dot™, connect the above, through the center of the Ather Dot™. wire that’s hanging from its face to the wire that’s hanging loose from its body.
- Page 9 How to connect your Ather Dot™ to the meter Neutral There are two ways to connect the Ather Dot™ Line to your meter. Read through to understand what suits you better. Direct connection (the preferred one) Via 6A socket Circuit Breaker...
- Page 10 3 pin 6A socket is a must for smooth and safe charging at all times. Note: In case you would like to install Ather Dot™ in a shared parking space in apartment complexes etc., it is advised to install a utility energy meter and connect the Ather Dot™...
- Page 11 Ather recommended additional accessories to make any pre-installed socket water resistant. Do not use the Ather Dot™ if it is defective, appears cracked, frayed, broken, or otherwise damaged, or if it fails to operate. To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- Page 12 A few monthly checks, keeping in condition. It poses a safety risk in the event of mind the cleaning tips and following actual electrical hazard on the Ather Dot™. the dos and don’ts will keep the Ather Dot™ well maintained. Here’s all you need to do.
- Page 13 The facade of the Ather Dot™, charging cable, and the connector end of the charging cable Note: Press the Reset Button to restore Ather Dot™, should be regularly wiped with a clean, dry cloth right after you have checked the PRCD Test Button.
- Page 14 Learn its language The Ather Dot™ - your home charging point, speaks to you. The changing state of the LED Other safety light communicates to you about how it’s doing. Every colour tells you something. instructions Solid amber light Your home charging point’s software is being...
- Page 15 Troubleshoot Transportation When transporting the Ather Dot™, handle it with If the LED on the Ather Dot™ shows a solid red care. Do not subject it to strong force or impact light, switch OFF the power for 10 seconds and or pull, twist, tangle, drag, or step on.
- Page 16 The use of Ather Dot™ - home charging point shall be governed by the terms and conditions of the agreement entered between you and Ather during purchase (’’Agreement’’).
- Page 17 Customer Support Number +91 7676 600 900...
Need help?
Do you have a question about the Dot and is the answer not in the manual?
Questions and answers