Advertisement
2.
introDuction anD oPeration
2.1
introDuction
Tough, aluminium bodied spotlight with integral LED map-reading light and heavy duty rubber impact guards. Ø90mm Lens and halogen
bulb produce 2-million candle power of intense white light, suitable for a variety of industrial, domestic and leisure applications. Features
slide dimmer switch, LED battery status display and locking power switch. 6Volt 4Ah battery gives around 25 minutes of continuous
operation. Supplied with in-vehicle charger and mains powered battery charger.
2.2
oPeratinG
WarninG! ensure you read, understand and apply safety instructions before use.
iMPortant Warranty inforMation:
the battery pack fitted to this cordless tool is considered to be a consumable item and its
ability to accept charge will reduce over time. We will warranty it against mechanical
and electrical defect for a period of one year - this does not cover fair wear and tear. If the
battery is not properly charged before first use, or regularly conditioned, its capacity will
diminish. Under these circumstances we will not replace the battery pack even if it is less
than one year old.
2.2.1 Charge the battery for 12-14 hours before first use. The battery pack will have been shipped
in a low charge state.
2.2.2 Turn spotlight ON and OFF by the trigger at the top of the handle. To lock the trigger use the
switch situated to the side of the trigger.
Do not completely discharge the battery before re-charging as this will shorten battery life.
To test the battery life press the button on the back of the unit. Green indicates the spotlight
is fully charged, red indicates that the battery is low.
2.2.3 There is a map reading LED located on the underside of the lamp unit. To initiate the LED
simply press the button on the rear of the LED unit.
2.3
Battery cHarGinG
WarninG! ensure you read, understand and apply safety instructions relating to the
battery and charger before use.
2.4
Mains PoWer cHarGinG
2.4.1 Remove battery (fig.1.b) from spotlight by pressing side buttons to release.
2.4.2 Stand the battery on a safe flat surface and place the charger adaptor (fig.1.C) over the
battery connector.
note: The battery is designed to fit into the charger one way only. This is to ensure that the positive
(+) and negative (-) polarities correspond. Align the + and - polarity marks on the base of the
battery with the + and - marks on the charger, insert the battery and press very slightly
downward to seat the battery firmly into the charging base.
WARNING! DO NOT try to force battery into the base with crossed polarities.
2.4.3 Connect the mains adaptor jack to the battery charger jack inlet. Plug into the mains power
supply and switch on.
The green LED will light up indicating that the power is on. The red LED light indicates that
the battery is correctly in contact with the charger and is charging.
2.4.4 Allow to fully charge for 11-12 hours. The red LED will remain on until the battery is removed
from the charger. The green light will remain until the power source is switched off.
2.4.5 Store the charger in a safe, dry location.
2.5
12V VeHicLe PLuG aDaPtor
2.5.1 Remove battery (item b) from spotlight by pressing side buttons to release.
2.5.2 Stand the battery on a safe flat surface and place the charger adaptor (fig.1.C) over the battery connector.
note: The battery is designed to fit into the charger one way only. This is to ensure that the positive (+) and negative (-) polarities
correspond. Align the + and - polarity marks on the base of the battery with the + and - marks on the charger, insert the battery and press
very slightly downward to seat the battery firmly into the charging base.
2.5.3 Plug the 12V vehicle plug adaptor into the charger adaptor inlet, and plug the other end of adaptor into vehicle accesory socket.
2.5.4 The charger LED lights will display as mentioned in 2.4.3. Allow approximately 9 -10 hours for charging.
2.5.5 When fully charged, unplug the adaptor from the vehicle socket and charger unit.
2.5.6 Store the adaptor in a safe, dry location.
note: Charging the spotlight from a 12 Volt vehicle socket will drain the vehicle battery.
3.
Maintenance
3.1
cHanGinG tHe LaMP BuLB
3.1.1 Disconnect the battery pack from spotlight and wait until the unit cools before attempting
to open the back.
3.1.2 Remove screws located at the top and bottom of the front rubber cover (fig.2.S).
3.1.3 Remove cover (fig.2.R) and slide the reflective cone out of the assembly.
3.1.4 Pinch the wire clip securing the bulb to release.
3.1.5 Replace the bulb and re-assemble in reverse order.
3.2
cLeaninG
Keep the spotlight clean. Do not use abrasives or solvents.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
iMPortant: No liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
inforMation: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
sole uK Distributor, sealey Group,
Kempson Way, Suffolk business Park,
bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
fig.3
ML2
PARTS FOR:
Replacement bulb. . . . . . . . . . . . . . . . . . . mL2.01
mains Charger . . . . . . . . . . . . . . . . . . . . . . mL2.C
Car Charger . . . . . . . . . . . . . . . . . . . . . . . mL2.CC
Charger Adaptor . . . . . . . . . . . . . . . . . . . . mL2.CA
battery Pack . . . . . . . . . . . . . . . . . . . . . . . .mL2bP
www.sealey.co.uk
01284 757500
Web
sales@sealey.co.uk
01284 703534
email
fig.2
mL2
Issue: 3 - 20/12/11
Advertisement
