Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Schiller Steiner 75-70644A
Summary of Contents for Schiller Steiner 75-70644A
- Page 1 MODEL: 75-70644A TURBINE BLOWER PB200...
- Page 2 CALIFORNIA WARNING Proposition 65 Warning Diesel engine exhaust and some The engine exhaust from this product of its constituents are known to the contains chemicals known to the State State of California to cause cancer, of California to cause cancer, birth birth defects and other reproductive defects or other reproductive harm.
-
Page 3: Table Of Contents
Schiller Grounds Care. Inc. designs and builds its equipment to serve many years in a safe and productive man- ner. For longest life, use this product only as directed in the manual, keep it in good repair and follow safety warnings and instructions. -
Page 4: Description / Specifications
DESCRIPTION / SPECIFICATIONS TURBINE BLOWER DESCRIPTION The PB200 Turbine Power Blower is designed to attach to the quick-hitch of Steiner power units. Noise pollution will not be a concern with this turbine power blower. Quiet but powerful, it quickly cleans walkways, parking lots, leaves, debris, and more. -
Page 5: Safety
Schiller of hazard seriousness. These words appear in this Grounds Care. Inc. Engineering Department. Any manual and on the safety labels attached to Schiller Schiller Grounds Care. Inc. product that is altered, Grounds Care. Inc. machines. For your safety and... - Page 6 SAFETY TURBINE BLOWER GENERAL SAFETY • Read and understand the owner’s manual, • Never allow anyone to operate or service this before attempting to operate this machine. machine while under the influence of alcohol or drugs. • Operate all controls from the operator’s seat, (if so equipped).
-
Page 7: Decals
DECALS TURBINE BLOWER Location: Main Frame Location: Turbine Housing Location: Front of Bumper Location: Discharge Nozzle... -
Page 8: Installation
INSTALLATION TURBINE BLOWER ATTACHING THE TURBINE POWER BLOWER • • Open the quick hitch latches and drive the Remove the clip pin from the support stand. tractor into position, aligning the quick hitch. Rotate the stand to the highest setting Be sure that both latches are fully engaged and insert clip pin. -
Page 9: Operation
OPERATION TURBINE BLOWER OPERATING THE TURBINE POWER BLOWER Controls • The Front Lift lever controls the lift. Normal operation is to have the lever in the “FLOAT” position. • The Auxiliary Hydraulic lever controls the position of the nozzle. It will rotate in a continuous 360 degree rotation. -
Page 10: Service
SERVICE TURBINE BLOWER SERVICE SCHEDULE ADJUSTMENTS Daily: Turbine drive belt: Remove the drive belt shield. Tighten the drive belt • Check for any signs of loose bolts and by loosening the front bearing mount bolts, move the tighten as needed. drive shaft with the adjusting screw, and re-tighten mount bolts. - Page 11 PARTS SECTION TURBINE BLOWER PARTS SECTION...
- Page 12 MAIN FRAME TURBINE BLOWER FIGURE 1...
- Page 13 MAIN FRAME TURBINE BLOWER FIGURE 1 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 4165649 S-MAIN FRAME 6110053.17 INTAKE SCREEN 6110015.17 STRAP-RETAINING 56-027 TRIM-4' 64139-04 BOLT-WLF 1/4-20X3/4 85010N S/B GREASE FITTING 4166688 BRACE 64-611.7 SHIELD-DRIVE PULLEY 4165469 SPACER-.76 X 1.25 X .188 4170936 KNOB-3 PRONG 1/4-20 4166687...
-
Page 14: Mounting Assembly
MOUNTING ASSEMBLY TURBINE BLOWER FIGURE 2... - Page 15 MOUNTING ASSEMBLY TURBINE BLOWER FIGURE 2 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 6110052.17 TURBINE MNTNG STAND 6110011.17 INTAKE SCREEN, LOWER 6110056.7 KICKSTAND 64139-21 BLT-WLF 3/8-16X3/4 64139-24 BLT-WLF 3/8-16 X 1 64163-87 WASHER, .391X1.375X12GA 2 99-F36 BOLT, LEG RETAINER 64141-13 NUT WLF 1/2-13 64168-1...
-
Page 16: Drive Parts / Hydraulics
DRIVE PARTS / HYDRAULICS TURBINE BLOWER FIGURE 3... - Page 17 DRIVE PARTS / HYDRAULICS TURBINE BLOWER FIGURE 3 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 6110052.17 TURBINE MNTG STAND 20-017 HOSE, 1/4 X 70 25-2503-10-6 FITTING-90 21-135 MOTOR-HYD 21-136 SEAL KIT 83-BS2816 PULLEY 81-A053 BELT-A53 SEE BELT CHART 83-BK5012 PULLEY-5"...
-
Page 18: Turbine Parts
TURBINE PARTS TURBINE BLOWER FIGURE 4... - Page 19 TURBINE PARTS TURBINE BLOWER FIGURE 4 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 83-H20 BUSHING, 1-1/4" H 83-BK65H PULLEY-6.5" H BUSHING 81-B050 BELT-B50 6110022.17 SPACER-NOZZLE RING 87-14-138ER BASE-NOZZLE RING 81-A053 BELT-A53 87-14-1600 SLIDE-NOZZLE 6110042 BOLT 87-14-139 BANDS-CLAMP 10 87-14-137 ELBOW-45 11 87-14-136B NOZZLE-10"...
-
Page 20: Decals
DECALS TURBINE BLOWER FIGURE 5 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 00-093 DECAL-OWNER'S MANUAL 4116761 DECAL-MADE IN AMERICA 00-282 DECAL-CLOSE CLEARANCE 1 00-286 DECAL-EYE PROTECTION 00-375 DECAL-THROWN OBJ HAZ 87-BT-4X4 DECAL-BUFFALO TURBINE 00-290 DECAL-ROT POS IND... -
Page 21: Belt Chart
BELT CHART TURBINE BLOWER FIGURE 6... - Page 22 SCHILLER GROUNDS CARE, INC. ONE BOB-CAT LANE P.O. BOX 469 JOHNSON CREEK, WI 53038 920-699-2000 ©Schiller Grounds Care, Inc. 2010 www.schillergc.com...