Summary of Contents for Simplified Building Easi-Dec
- Page 1 VERTICAL LADDER WITH CAGE INSTALL INSTRUCTIONS Incorporating Lock Out Gate and Exclusion Zone Kits...
-
Page 2: Table Of Contents
LADDER SYSTEM ASSEMBLY INSTRUCTIONS SECTION CONTENTS PAGE INTRODUCTION Validity Authorised Agent Health and Safety Familiarisation Certifying Body Anticipated Life Safeguarding the Instruction For Use Manual Copyright Amendment Service 1.10 Modifications to The Ladder System 1.11 Definition “Authorised Person” 1.12 Definition “Trained Person” 1.13 Use in Accordance with Regulations 1.14... -
Page 3: Introduction
Installers and users must comply with all relevant health and safety regulations in their given territory. force in the country of use; and can assess the safe working conditions of the installation location. A trained person shall be responsible for selecting all users of The Easi-Dec Ladder System. -
Page 4: Incorrect Use
The requirements the manufacturer places on the users of The Easi-Dec Ladder System are as ®... -
Page 5: Basic Safety Instructions
INTRODUCTION 2. BASIC SAFETY INSTRUCTIONS Basic safety instructions for the safe handling of the Easi-Dec Ladder System can be found here. ® DANGER TO LIFE! It is imperative that you follow these safety instructions to avoid endangering your life and safety. -
Page 6: Installation
If some of the parts listed in the parts list or on the delivery note are missing or damaged, then you must replace them with original parts. Contact the manufacturer to obtain these. Note: A complete list of all parts and details on the total weight of the Easi-Dec Ladder System are ®... - Page 7 LADDER SYSTEM ASSEMBLY INSTRUCTIONS C. Attach large hoops to top and lower of upright posts as sown A. Attach upright posts with brackets to top of ladder using M10 x B. Install GRP step at top of ladder, securing using M10 x 40 above using M10 x 80mm screws, flat washers and nyloc nuts.
- Page 8 LADDER SYSTEM ASSEMBLY INSTRUCTIONS I. Secure ladder to wall and torque set wall fixings as per G. Attach vertical strengthening flat bars between to each hoop H. Line ladder up with wall in required location and mark holes manufacturers instructions. Check all torque settings on ladder using M10 x 40mm screws, flat washers and nyloc nuts.
- Page 9 LADDER LOCKOUT PANEL ASSEMBLY & INSTALLATION Installation on the Exclusion Zone The lock out panel product helps prevent use of ladders by unauthrosied persons. PLEASE NOTE - A padlock with a 80mm shackle with a diameter not larger than 6mm is required to lock the panel to the ladder.
- Page 10 LADDER LOCKOUT SYSTEM ASSEMBLY INSTRUCTIONS C. Once panel is hooked over the ladder and held in position, add A. The kit contains lockout plate and securing clamp. A suitable B. At a suitable height, line the integrated hook of the lock out the C clamp by clamping around the rung and threading through 80mm long, 6mm diameter shackle padlock is required (not panel up with rung of ladder and hook ladder over rung.
- Page 11 LADDER EXCLUSION ZONE PLANNING ASSEMBLY & INSTALLATION Installation on the Exclusion Zone The Exclusion Zone product creates an area directly below the ladder that should only be entered if no-one is using the ladder. The kit consists of two guardrail frames and a powdercoated KEE GATE. PLEASE NOTE - Suitable wall and floor fixings are required to secure the gurardrail to a wall and ground surfaces.
- Page 12 LADDER EXCLUSION ZONE ASSEMBLY INSTRUCTIONS C. Attach 61-8 fitting to ground and wall surfaces using suitable A. Attach 10-8, 62-8 and 15-8 KeeKlamp fittings to upright B. Connect 61-8 fittings to the horzintal tubes and connect fixings. Following fixing manufacturers guidance for correct tube.
-
Page 13: Pre Use Checks
LADDER SYSTEM PRE-USE CHECKS Always carry out a risk assessment and method statement Before each use, check ladder thoroughly for corrosion, signs of vandalism, and damage. Always ensure that the area below where you are working is clearly marked to warn people of works above. Follow HSE guidelines when working at height. -
Page 14: Recertification
LADDER SYSTEM RECERTIFICATION Periodic inspections by a competent person are required under the Temporary Work Equipment Directive 2009/104/EC – use of work equipment and Section 12 of the Work at Height Regulations. The frequency will depend upon environment, location and usage, but should be at least every 12 months or before and after each use whichever soonest. Visually inspect the complete system before installation ensuring all component parts are present. - Page 16 Simplified Building Tel: 01384 476 107 Unit A2, Cradley Business info@simplifiedsafety.co.uk Park Cradley Heath, Birmingham B64 7DW LCK_V1_23.8.19...
Need help?
Do you have a question about the Easi-Dec and is the answer not in the manual?
Questions and answers