Related Manuals for Sentry MVS
Summary of Contents for Sentry MVS
- Page 1 Original Instructions Installation, Operation & Maintenance Manual Sentry MVS Sampler Low Emission Samplers S-MS-IOM-00261-5 01-21...
-
Page 2: Table Of Contents
Sentry Equipment Corp instructions. Otherwise, injury, damage, or both may result. Copyright © 2018 by Sentry Equipment Corp. All rights reserved. All product and company names are property of their respective owners. This document contains proprietary information. No part of this document may be photocopied or reproduced without the prior written consent of Sentry Equipment Corp. -
Page 3: Safety Information
NOTE Information that requires special emphasis. TIP Alternate techniques or clarifying information. SHALL: This word is understood to be mandatory. SHOULD: This word is understood to be advisory. Sentry MVS Sampler... -
Page 4: General Safety Precautions
If the sample container is removed from the sampler, do not insert any body part or other item into the sample discharge port. Crushing will occur. Sentry Equipment Corp... -
Page 5: General Description
Tube Stub Type The Sentry MVS also has a tube stub option, which works in a similar fashion to the needle style; however, the sample is injected into the bottle via a tube stub in lieu of needles. A vent hole in the tube stub assembly vents gases from the bottle and prevents pressure buildup in the sample bottle. -
Page 6: Specifications
500 ml 32 oz (1000 ml) 2000 ml Boston Round bottle cap/thread interfaces per GPI finish standards. Schott bottle cap/thread interfaces per ISO 4796. Standard septum material is Teflon-coated silicone. Other bottle or septum arrangements are available. Sentry Equipment Corp... -
Page 7: Installation
Installation The MVS manual low-emission sampler can be supported directly by the top 1/4 in (or optional 3/4 or 1/2 in) compression connection or mounted to a panel using the bracket provided. When installing the valve assembly, verify that adequate space has been provided for the removal of the bottle from the shroud or bottle adapter. - Page 8 The needle assembly has positive engagement to insure that the needles are correctly positioned prior to insertion. Needle Assembly The locating pin must fit into the locating hole. Sentry Equipment Corp...
-
Page 9: Maintenance
Sentry sample coolers. Carbon Canister An optional Sentry carbon canister is available. The carbon canister assembly is designed to absorb hydrocarbon gases vented from Sentry manual low-emission samplers. The gas vent of the sampler panel is connected to the inlet of the carbon canister assembly. The gases then pass through a volume of activated carbon, where hydrocarbons, such as benzene, are absorbed. -
Page 10: Troubleshooting
2. Fill the container with activated carbon (or impregnated activated carbon) to about 1 in from the top of the container. 3. Place approximately 2 in (uncompressed thickness) of glass wool (Sentry part number 4-04825A) at the bottom of the container. -
Page 11: Standard Warranty
6-04081C Standard Warranty Sentry Equipment Corp (“Seller”) warrants products manufactured by it and supplied hereunder (“Products”) to be free from defects in workmanship and, to the extent materials are selected by Seller, to be free from defects in materials, in... -
Page 12: Customer Support
ƒ Field Service & Retrofi ts—When a problem needs immediate attention. ƒ Replacements Parts & Consumables—Order your replacement parts and consumables. ƒ Sentry ProShield Services – select from four ProShield Guardian service plans providing diff erent levels of support to protect your large system investments with regularly scheduled maintenance. - Page 13 This page is intentionally left blank. Sentry MVS Sampler...
- Page 14 Serving customers in more than 50 countries across six continents worldwide. sentry-equip.com 966 Blue Ribbon Circle North, Oconomowoc, WI 53066 U.S.A. | +1-262-567-7256 | support@sentry-equip.com...