Table of Contents
Advertisement
Quick Links
ADPT TY80S-FCB2 FCB Auto Draw Valve Conversion Kit
This kit converts the Flavor Burst
When attached to an FCB freezer, this system allows for push-button dispensing without the use of a draw handle.
This kit also includes a purge feature to help reduce flavor carryover between servings. The following instructions are
for a field conversion of the freezer. For more information, please contact your local Flavor Burst
NOTE: BE SURE THE FCB FREEZER IS EMPTY OF PRODUCT BEFORE INSTALLING THIS KIT.
ADPT TY80S-FCB1
FCB 126
DRAW SWITCH
HOUSING ASSEMBLY
CYLINDER
ASSEMBLY
FCB 112
MODIFIED SPOUT
Determine which side, left or right, the Auto Draw Valve
1
Assembly is to be installed. Remove the freezer door and
spout assembly from the freezer.
REV021313
Flavor Burst
®
FB 80Sa frozen beverage system to a Flavor Burst
CONNECTOR & LINE
FCB 237
CABLE MOUNTING PLATE
ASSEMBLY & 'D' ROTOR CABLE
EPROM
Installation
FCB 141B
PANEL MOUNT
FCB 140
TEE & C TUBE
(FCB 127R
vent bracket)
FCB 142
FIX 1036
Elbow
Connector
Remove and disassemble the draw spout. Set aside the
2
cap, spring and valve for use with the modified assembly.
®
®
auto draw valve FCB system.
MAN 80FCB-OM
Auto Version
Operations Manual
FCB 138A AUTO DRAW
VALVE ASSEMBLY
(FAS 2014
8-32 x 1/2" screws x2)
DRAW HANDLE PIN ASSEMBLY
TAY 039321
TAY 046193-BLA
(x2)
®
distributor.
ADPT TY80S-FCB2
INJ 201A
Syrup Line
Manifold
TEMPLATE
FAS 2135
Truss Screws (x2)
pg. 1 of 6
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Flavor Burst ADPT TY80S-FCB2
- Page 1 This kit also includes a purge feature to help reduce flavor carryover between servings. The following instructions are ® for a field conversion of the freezer. For more information, please contact your local Flavor Burst distributor. NOTE: BE SURE THE FCB FREEZER IS EMPTY OF PRODUCT BEFORE INSTALLING THIS KIT.
- Page 2 ADPT TY80S-FCB2 FCB Auto Draw Valve Conversion Kit Install the Cylinder Assembly on the modified door spout Install the valve, spring and cap to the door spout by sliding the bracket over the threaded portion of the assmbly. Then install the assembly onto the freezer door.
- Page 3 ADPT TY80S-FCB2 FCB Auto Draw Valve Conversion Kit Reinstall the front service panel with the connector Remove the side service panel nearest the connection. securely in place and tubing to the inside. Ensure the cable falls against the panel and under the support bar so that it does not interfere with any internal freezer parts.
- Page 4 ADPT TY80S-FCB2 FCB Auto Draw Valve Conversion Kit Slide the bracket down and turn the side screws to brace Connect the female spade connectors of the Rotor Cable the assembly against the freezer. D to the male connectors on the D Valve.
- Page 5 Remove the cabinet cap and replace the E-prom near the Remove the back cover of the Flavor Burst cabinet and back with the E-prom provided in the kit. Be sure to locate the sanitizer pump near the base.
- Page 6 ADPT TY80S-FCB2 FCB Auto Draw Valve Conversion Kit Disconnect and remove the push-to-connect tee Install the kit’s push-to-connect elbow connector to the connector from the two elbow connectors and the Pump Pump Flush Tube and the sanitizer tank tube. Flush Tube.
Need help?
Do you have a question about the ADPT TY80S-FCB2 and is the answer not in the manual?
Questions and answers