CarVision BMW-CIC-LVDS Quick Start Manual

CarVision BMW-CIC-LVDS Quick Start Manual

Bmw monitors with 4pin hsd lvds connector, video-inserter with 2 video + rgb + rear-view camera input and can control

Advertisement

Quick Links

Video-inserter
BMW-CIC-LVDS
BMW monitors
with 4pin HSD LVDS connector
Video-inserter with 2 video + RGB + rear-view camera input and CAN control

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BMW-CIC-LVDS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for CarVision BMW-CIC-LVDS

  • Page 1 Video-inserter BMW-CIC-LVDS BMW monitors with 4pin HSD LVDS connector Video-inserter with 2 video + RGB + rear-view camera input and CAN control...
  • Page 2: Table Of Contents

    Contents 1. Prior to installation 1.1. Delivery contents 1.2. Checking the compatibility of vehicle and accessories 1.3. Dip-switch settings 1.3.1. Vehicle selection (dip 6-8) 1.3.2. Enabling the interface’s video inputs (dip 1-3) 1.3.3. Rear-view camera settings (dip 5) 1.3.4. RGB settings 2.
  • Page 3: Prior To Installation

    Product features  RGB-input for after-market navigation  2 video-inputs for after-market devices (e.g. DVD-Player, DVB-T tuner, …)  Built-in audio-switch  Rear-view camera input, automatically switching  Factory rear-view camera compatible  Switching of video through factory infotainment buttons ...
  • Page 4: Checking The Compatibility Of Vehicle And Accessories

    1.2. Checking the compatibility of vehicle and accessories Requirements General monitor with 4pin HSD LVDS video connector Vehicle 1series (E87), 3series (E90/91/92), 5series (E60/61/F10/F11), 6series (E63/64/F12/F13), 7series (F01/F02), GT5 (F07), X1 (E84), X3 (F25), X5 (E70), X6 (E71), Z4 (E89) and other vehicles Navigation/Radio Professional Navigation CIC (also few CCC) Business Navigation M-ASK from about 2009...
  • Page 5: Enabling The Interface's Video Inputs (Dip 1-3)

    1.3.2. Enabling the interface’s video inputs (dip 1-3) Only the enabled video inputs can be accessed when switching through the video sources. It is recommended to enable only the required inputs for the disabled will be skipped when switching through the video interfaces inputs. Video-input ON (down) OFF (up)
  • Page 6: Installation

    2. Installation Switch off ignition and disconnect the vehicle’s battery! The interface needs a permanent 12V source. If according to factory rules disconnecting the battery is to be avoided, it is usually sufficient to put the vehicle is sleep-mode. In case the sleep-mode does not show success, disconnect the battery with a resistor lead.
  • Page 7: Connections

    2.2. Connections 4pin HSD LVDS female connector of interface harness Keypad for video source switching (additional option) Audio cable Backside factory monitor 4pin HSD LVDS 4pin HSD female connector interface of vehicle harness LVDS cable Video interface Pin-definition white 6pin power connector Pin 1 (yellow) - ACC or Battery +12V Pin 2 (red)
  • Page 8: Installation Procedure - Function Check

    2.3. Installation procedure – function check Follow the below procedure using the “Connections” scheme from chapter 2.2. as reference. Before the installation of the sources and the interface we recommend a first quick connection of the interface and test run to ensure that vehicle and product are compatible. Due to changes in production of the vehicle manufacturer there is always the possibility of incompatibility.
  • Page 9: Audio Insertion

    2.5. Audio insertion This interface can only insert video into the factory infotainment. The video can be activated to any audio mode of the factory infotainment. If an AV-source is to be connected, the source’s video out is connected to the video IN1 of the video interface and the source’s audio out to the audio insertion.
  • Page 10: Interface Operation

    3. Interface operation 3.1. By factory infotainment buttons Some of the factory buttons can be used to execute interface functions. Longpress NAV (MAP)(more than 1 second) to activate the interface video. Each longpress will switch to the next enabled input. If all inputs are enabled the order is: ...
  • Page 11: Specifications

    4. Specifications BATT/ACC range 7V ~ 25V Power 0.3A @12V Video input 0.7V~1V Video input formats PAL/NTSC Weight 195g Dimensions (box only) B x H x T 182 x 24 x 100 mm...

Table of Contents