Feit Electric 1286740 Instructions

MODEL SHOP/840/LED
ITM. / ART. 1286740
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
WARNING:
These products may represent a possible shock or re hazard if improperly installed or attached in any way. Products should be
installed in accordance with the owners manual, current electrical codes and/or the current National Electric Code (NEC).
PARTS INCLUDED (Drawings not to scale)
screw hooks V-hooks hanging chains
x2 x2
CAUTION, IMPORTANT SAFETY INSTRUCTIONS
This portable light-emitting-diode (LED) luminaire has a polarized plug (One blade is wider than the other) as a feature to reduce the risk of electric shock. This
plug will t in a polarized outlet only one way. If the plug does not t fully in the outlet, reverse the plug. If it still does not t, contact a quali ed electrician.
Never use with an extension cord unless plug can be fully inserted. Do not alter the plug.
LINKING MULTIPLE SHOPLIGHTS
Connect to
Power Outlet
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation. Note: This equipment has been tested
and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between
the equipment and receiver. Connect the equipment into an outlet on a circuit
di erent from that to which the receiver is connected. Consult the dealer or an
experienced radio/TV technician for help. Any changes or modi cations not
expressly approved by the manufacturer could void the user's authority to
operate the equipment.
FEIT ELECTRIC COMPANY | PICO RIVERA, CA | (800) 543-3348 | www.feit.com
wall anchors mounting screws
x2 x3 x3
46.96 in. / 1.19 m
42.20 in. / 1.07 m
48 in. / 1.2 m
Link up to 4 shoplights together
pull chain extension cable tie
x1 x1
5.25 in
13.33 cm
1.95 in / 4.9 cm
Connect to
additional shoplight
LIMITED WARRANTY
This product is warrantied to be free from defects in workmanship and materials
for up to ve years from date of purchase. If the product fails within the warranty
period, please contact Feit Electric at info@feit.com, visit feit.com/contact-us or
call 1-866-326-BULB (2852) for instructions on replacement or refund.
REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT
PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN
DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and
provinces do not allow the exclusion of incidental or consequential damages, so
the above limitation or exclusion may not apply to you. This warranty gives you
speci c legal rights, and you may also have other rights which vary from state to
state or province to province.
For comments please contact:
Feit Electric Customer Service Department
4901 Gregg Road, Pico Rivera, CA 90660
NOTE: When used with wall switch,
make sure pull chain switch is On.
When using pull chain On/O switch, attach
included extension to pull chain.
THIS FIXTURE IS INTENDED TO ONLY BE
INSTALLED DIRECTLY BENEATH A
CEILING MOUNTED RECEPTACLE.
CAUTION:
Installation not
be made on a radiant-heating ceiling.
CAUTION:
Hooks are to
engage the chain only and not the
electric cord.
Voltage: 120Vac Current: 0.37A
SUITABLE FOR DAMP LOCATION
Maximum distance between
interconnected units: 65 in. (1.65m)