Subscribe to Our Youtube Channel
Summary of Contents for Power smart PS6120
- Page 1 INSTRUCTION MANUAL Pneumatic 21ºRound Head Framing Nailer Model # PS6120 Have product questions or need technical support? Please feel free to contact us! Website: www.Amerisuninc.com Toll free: 1-800-791-9458 M-F 9-5 EST Email: support@amerisuninc.com...
-
Page 3: Table Of Contents
Assembly ………………………………………………………………… 9 Operating instruction…………………………………………………..9 Maintenance.……………………………………………………………… 12 Troubleshooting…………………………………………………………. Exploded view & parts list……………………………………………… Warranty………………………………………………………………… TECHNICAL DATA Pneumatic 21ºRound Head Framing Nailer Model # PS6120 Fastener angle: 21º Fastener length : 2" – 3 1/2" Fastener: 0.113"-0.130" diameter Magazine capacity: Air inlet (NPT): 1/4"... -
Page 4: General Safety Rules
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert, and knowing how your framing nailer works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: Do not operate this unit until you read this instruction manual for safety, operation and maintenance instructions. WARNING: This product contains chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm. - Page 5 contact trip is adjusted when the tool is connected to the air supply and nails are loaded, accidental discharge may occur. Connect tool to air supply before loading fasteners, to prevent a fastener from being fired during connection. The tool driving mechanism may cycle when tool is connected to the air supply. Do not load fasteners with trigger or contact trip depressed, to prevent unintentional firing of a fastener.
- Page 6 Refer to the Maintenance and Repairs sections for detailed information on the proper maintenance of the tool. Always operate the tool in a clean, lighted area. Be sure the work surface is clear of any debris and be careful not to lose footing when working in elevated environments such as rooftops. Do not drive fasteners near edge of material.
- Page 7 Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. WARNING: ALWAYS USE SAFETY GLASSES.
-
Page 8: Knowing Your Framing Nailer
KNOWING YOUR FRAMING NAILER Magazine Trigger Safety contact trip Exhaust deflector 1/4" Air quick coupler Magazine handle Magazine latch Unpacking Unpack the framing nailer and all its parts, and compare against the list below. Do not discard the carton or any packaging materials. Please call 1-800-791-91458 or E-mail us at support@amerisuninc.com any parts are damaged or missing. -
Page 9: Assembly
PowerSmart PS6120 Pneumatic Framing nailer drives 21-degree round head framing nails from 2" to 3-1/2" (50 mm to 90 mm) in length. The tool has a die cast aluminum body for strong and light weight design. - Page 10 WARNING: Never load nails with the contact trip or trigger activated. Personal injury may result. When replacing nails in your model PS6120, follow these guidelines: Nail Type: 21 degree round head framing nail Length: 2"-3 1/2" Diameter: 0.113" – 0.130"...
- Page 11 5. Pull the trigger. -If the nail drove into the wood for enough, continue with your intended operations. -If the nail either went too far or not far enough, then refer to Adjusting Depth subsection. WANRNING: During operation, this nailer can propel objects into the air and exhaust concentrated bursts of air, causing immediate eye damage.
-
Page 12: Maintenance
2. Never exceed maximum and minimum pressure. Too low or too high pressure would cause noise wear and tear or misfiring. 3. When connecting air supply always keep hands and body away from discharge area of tool. 4. A filter- regulator-lubrication is required and should be located as close to tool as possible. 5. -
Page 13: Troubleshooting
TROUBLE SHOOTING The following form lists the common operating system with problem and solutions. Please read the form carefully and follow it. WARNING: If any of the following symptoms appears during your operating, stop using the tool immediately, or serious personal injury could result. Only a qualified persons or an authorized service center can perform repairs or replacement of tool. - Page 15 Item Stock # Description Item Stock # Description Compression spring Bolt M8x16 PS6120-049 PS6120-001 PS6120-050 Safety yoke Exhaust deflector PS6120-002 PS6120-051 Bolt M5x10 Deflector rubber PS6120-003 PS6120-052 Spring washer 5 Compression spring PS6120-004 PS6120-053 Flat washer 5 Spring wire PS6120-005...
- Page 16 (2) years from date of purchase. Ninety (90) days for all Power Smart Products, if the tool is used for professional or commercial use. SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Two (2) Years Limited...
Need help?
Do you have a question about the PS6120 and is the answer not in the manual?
Questions and answers