Advertisement
2. INTRODUCTION
High velocity pedestal fan suitable for movement of huge volumes of air. Carefully balanced
and fully guarded blades provide quiet and safe operation. Three-speed power selection and
height-adjustable stand allow precise control of air flow to exactly where it is needed. Fitted
with BS approved plug. Suitable for use in industrial, commercial, agricultural and automotive
workshop and showroom applications.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . HVSF18
Fan Diameter:. . . . . . . . . . 450mm(18")
Speeds: . . . . . . . . . . . . . . . . . . . . . . . 3
Height: . . . . . . . . . . . . . 1240-1450mm
4. ASSEMBLY & OPERATION
4.1.
Remove all packaging material.
4.2.
Attach the mounting pole to the circular base using the four larger nuts and bolts
supplied as shown in Fig.3. Ensure the nuts are properly seated in the pockets on the
underside of the moulded plastic base. Slide the plastic cover down to cover the bolts.
4.3.
Attach the semi-circular fan mounting yoke to the chrome extension pole using the
two clamping pieces, nuts and bolts as shown in Fig.1
IMPORTANT: Ensure that all safety instructions from section 1 have been read and
understood before using the fan.
4.4.
Set the fan on a level, dry surface.
4.5.
Plug the power cord into the mains supply.
4.6.
The fan features 3 speeds which are selectable using the control buttons located at
the back of the fan above the motor. See Fig.4. LOW (1) or MED (2) settings will suit
most needs, HIGH (3) is used for maximum air movement.
4.7.
Adjust the direction of air flow by tilting the fan assembly to the required angle.
4.8.
Adjust the height of the fan by slackening the clamp sleeve on the black section of the
pole. Slide the chrome tube up or down as required and retighten the clamp.
4.9.
When not in use, disconnect from power supply and store in a safe, dry, childproof location.
5. CARE OF FAN
IMPORTANT: Turn the fan OFF (0) and disconnect from power supply before cleaning.
5.1.
Use only a soft, damp cloth to clean the fan.
5.2.
DO NOT immerse the fan in water and NEVER allow water to drip into the motor housing.
5.3.
DO NOT use solvents or other chemicals to clean the fan.
5.4.
To clean the fan blades, loosen the screws in the grill ring, unclip the fastenings around
the ring and lift the front grill.
5.5.
Wipe the blades and grills.
5.6.
Reassemble the front grill onto the fan by engaging the fastenings and retightening the
screws.
5.7.
Store the fan in its original box or cover the fan to protect it from dust and store in a
safe, dry, childproof location.
Fig.4
Declaration of Conformity
18" IND. HIGH VELOCITY PEDESTAL FAN
Model HVSF18.V2
89/336/EEC EMC Directive
73/23/EEC Low Voltage Directive
93/68/EEC CE Marking Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address including your postcode.
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
Motor Power: . . . . . . . . . . . . . . . . 90W
Supply: . . . . . . . . . . . . . . . . . . . . 230V
Current: . . . . . . . . . . . . . . . . . . . . 0.5A
Fig.3
We, the sole importer into the UK, declare that the product listed below is in conformity with the following EEC standards and directives
The construction file for this product is held by the Manufacturer and may be inspected on request by contacting Jack
Sealey Ltd.
Signed by Mark Sweetman
01284 757500
20th November 2006
sales@sealey.co.uk
01284 703534
e-mail
Fig.1
For Jack Sealey Ltd.
Sole importer into the UK
of Sealey Power Products.
www.sealey.co.uk
Web
HVSF18.V2 - 1 - 20/11/06
Fig.2
Advertisement
