LDT Adap HSI-S88-N-F Operation Instruction

L D T
ittfinski aten echnik (
Operation Instruction
3-fold s88-N Adapter
Adap-HSI-s88-N
From the Digital-Professional-Series!
Adap-HSI-s88-N-F
LDT-Part-No.:
>> finished module <<
With the Adapter Adap-HSI-s88-N is it possible to
connect s88-Feedback Modules such as RM-88-N,
RM-88-N-O and RM-GB-8-N directly by use of the
screened Patch-Cable to the Interfaces HSI-88,
HSI-88-USB and DiCoStation in accordance to
s88-N
.
This product is not a toy! Not suitable for children under 14 years of age! The kit
contains small parts, which should be kept away from children under 3! Improper
use will imply danger or injuring due to sharp edges and tips! Please store this
instruction carefully.
CE Part-No.:
44 40 21
Introduction/Safety Instruction:
You have purchased
Adap-HSI-s88-N that is supplied within the assortment of
Littfinski DatenTechnik (LDT).
We wish you having a good time using this product.
• Please read the following instructions carefully. Warranty will
expire due to damages caused by disregarding the operating
instructions. LDT will also be not liable for any consequential
damages caused by improper use or installation.
The adapter comes with a 24 month warranty.
Connecting the Adapter to the Interfaces
HSI-88, HSI-88-USB or DiCoStation:
• Attention: Please switch off your model railway layout
and unplug all transformers from AC-current before
starting to assemble the unit.
Connect the three 6-poles socket bars of the adapter Adap-
HSI-s88-N to the three 6-poles pin bars of the Interfaces HSI-
88, HSI-88-USB or the DiCoStation.
Please attend careful that there is no offset between the
position of the socket bars and the pin bars.
For the three s88-buslines are now RJ-45 Sockets available
s88-N
for realizing s88-bus connections to the feedback
modules by using screened Patch-Cables.
LDT
)
038112
the 3-fold s88-N Adapter
The PC-board of the adapter Adap-HSI-s88-N contains three
RJ-45 sockets for three s88-buslines marked with „Left",
„Middle" and „Right" for the left, middle and right bus lines to
the feedback modules.
Digital-Profi werden!
High Speed Interface-88
HSI-88-USB
Schnelles Computer-Interface für den s88 Rück-
meldebus. Ermöglicht drei s88 Rückmeldestränge.
LED1
GO
USB
ST1
The draft shows the High Speed Interface HSI-88-USB with
connected Adapter Adap-HSI-s88-N.
Further LDT-Products from the Digital-
Professional-Series:
S-DEC-4
4-fold turnout decoder for four outputs and with free
programmable decoder address. With possible external power
supply.
SA-DEC-4
4-fold switch decoder with four bi-stable relays of 4A switching
current each and free programmable decoder address.
RM-88-N
16-fold feedback module (such as Märklin s88 switching
against ground) for the s88-standard connection and
RM-88-N-O
16-fold feedback module with galvanic separated opto
coupling inputs for high interference protection and for
potential separation.
For s88-Standard Connection and
RM-GB-8-N
8-fold feedback module with 8 integrated track occupancy
detectors for a max. current load of 3 Ampere (peak current
of up to 7 Ampere) for s88-standard connection and
All components are available as easy to assemble complete
kits as finished modules or as finished modules in a case.
Littfinski DatenTechnik (LDT)
D-25492 Heist
www.ldt-infocenter.com
Littfinski DatenTechnik (LDT)
LED2
ST2
BOOSTER
STOP
ST6 EXT-PORT
s88-N
.
s88-N
s88-N
.
.