Advertisement
Quick Links
Advertisement
Summary of Contents for iBell Tools MC25-84
- Page 1 MARBLE CUTTER MC25-84...
-
Page 3: Table Of Contents
TABLE OF CONTENTS 1. GENERAL POWER TOOL SAFETY WARNINGS __________ 2. MARBLE CUTTER SAFETY WARNINGS_________________ 3. PRODUCT OVERVIEW _________________________________ 4. PRODUCT SPECIFICATIONS ___________________________ 5. SETUP _________________________________________________ 6. PRODUCT FUNCTIONS AND ASSEMBLY________________ 7. GENERAL OPERATION ________________________________ 8. TROUBLESHOOTING __________________________________ IBL MC25-84... -
Page 4: General Power Tool Safety Warnings
Keep it away from heat, oil, sharp edges or moving parts. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. IBL MC25-84... - Page 5 When servicing a power tool, use only identical replacement parts. Follow instructions in the maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of shock or injury. IBL MC25-84...
- Page 6 Injuries and damage to property due to broken cutting attachments or the sudden impact of hidden objects during use. Danger of injury and property damage caused by other objects or due to natural reactions or calamities. IBL MC25-84...
-
Page 7: Marble Cutter Safety Warnings
Wear ear protectors. Exposure to noise can cause hearing loss. Wear safety goggles or eye protection when using this power tool. For additional protection against electric shock, be sure to wear rubber gloves. IBL MC25-84... - Page 8 Fully unwind the extension cords inorder to avoid potential overheating. Misuse or failure to follow the safety rules stated in WARNING! this instruction manual may cause serious personal injury. IBL MC25-84...
-
Page 9: Product Overview
PRODUCT OVERVIEW 1. Base plate 6. Cutting depth guide 2. Bevel locking bolt 7. ON/OFF switch 3. Bevel scale plate 8. Lock on button 4. Cutting wheel 9. Carbon brush compartment 5. Cutting depth locking knob IBL MC25-84... -
Page 10: Product Specifications
The product must be fully assembled before WARNING! operation! Do not use a product that is only partly assembled or assembled with damaged parts! Follow the assembly instructions step-by-step and use the pictures provided as a visual guide to easily assemble the product! IBL MC25-84... -
Page 11: Product Functions And Assembly
For continuous operation, press the lock on button (8) as well. Release the trigger switch to stop. Before plugging in the tool, always check that the WARNING! switch trigger actuates properly and returns to the "OFF" position when released. IBL MC25-84... - Page 12 The cutter can be adjusted to cut at angles between 0° and 45°. Always make a trial cut in a scrap piece of material along a guideline to determine how much you should offset the cutting wheel from the guideline to make an accurate cut. IBL MC25-84...
- Page 13 The direction in which the cutting wheel rotates has to be the NOTE: same as the direction of the arrow marked on the guard. After replacing the cutting wheel, make sure that the cutting wheel runs freely by turning the cutting wheel by hand. IBL MC25-84...
- Page 14 Connect it tightly on a faucet (tap) to feed water, Adjust the amount of water flow by simply adjusting the regulator. I Water pipe II Vinyl tube III Adaptor IV Faucet Tightening the water pipe assembly IBL MC25-84...
-
Page 15: General Operation
Always switch the product off, disconnect the product from the NOTE: power supply and let the product cool down before performing inspection, maintenance and cleaning work! Only perform repairs and maintenance work according to these instructions! All further works must be performed by a qualified specialist! IBL MC25-84... - Page 16 If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. IBL MC25-84...
- Page 17 Only use accessory or attachment for its stated purpose. This product does not contain any parts that can be repaired by the consumer. Contact an authorised service centre or a similarly qualified person to have it checked and repaired. IBL MC25-84...
-
Page 18: Troubleshooting
5.1 Conduct the 5. Machine operation correctly. overheating 5.2 Motor bearing 5.2 Check or replace it damage. by technician. All further inspection and repair work must be WARNING! performed by an authorised service centre or a qualified technician! IBL MC25-84... - Page 19 Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice. Do not dispose this product by normal household waste, but take it to a collection point and recycling of electrical and electronic equipment.