Advertisement
3. SPECIFICATION
model no: .................................................................bt2002.V2
rated battery Voltage ..................................................... 6-12V
charging system capability ......................................... 12, 24V
rated systems .................................... sAe, din, en, iec, Jis
test range ....................... 40-2100ccA en, 40-2000ccA sAe,
...................................................................... 30-1500ccA iec
......................................................................25-1300ccA din
........................................................... bY bAtterY tYPe Jis
minimum power requirement ............................................. 1.5V
note: ccA = cold cranking Amps
4. OPERATION
WARNING! ensure that you read, understand and apply the safety and operational instructions before connecting the tester clamps to
‰
the battery. only when you are sure that you understand the procedures is it safe to proceed with the testing process.
WARNING! Ensure that the vehicle, or battery, is in a well ventilated area before starting to test.
‰
check battery casing for cracks or leakage. if damage is found DO NOT test and replace battery.
4.1.
4.2.
clean battery terminals.
4.3.
if possible, check electrolyte levels and top-up with distilled water as necessary.
4.4.
unless otherwise specified tests are carried out with all electrical items switched off. Leaving any items on (boot light, interior light,
etc.) can result in expensive misdiagnosis.
4.5.
confirm that the 9V alkaline battery (supplied) is correctly fitted in the compartment in the rear of the tester.
Note that no results will be displayed until the tester is connected to a vehicle battery.
4.6.
connect the red clamp to the positive (+) battery terminal and the black clamp to the negative (-) terminal. When the internal battery
becomes discharged the display will read rePlAce internAl 9V drY bAtterY.
4.7.
if there is a poor connection the display will read CHECK CLAMPS, otherwise the display will read either BATTERY TEST, SYSTEM
TEST or LANGUAGE.
4.8.
by pressing the ▲▼ buttons the display will cycle through the three options. Press the enter button when the option you require is
displayed.
4.9.
to select a different language press enter when the word lAnGuAGe is displayed.
4.10.
using the up/down buttons select the language of your choice from english, french, German, spanish, italian, Portuguese or Japanese.
4.11.
When the language you require is displayed press the enter button to confirm your choice.
4.12.
BATTERY TEST (6 OR 12V)
4.12.1.
select 'bAtterY test' using the ▼▲buttons. Press the enter button to confirm your selection.
4.12.2.
the display will now prompt you to select bAtterY tYPe.
4.12.3.
using the ▼▲ buttons select either regular liquid, AGm flat Plate, AGm spiral or VrlA/Gel. Press the enter button to confirm your
selection.
4.12.4.
the display will now prompt you to select an appropriate rating standard. (select rAtinG)
4.12.5.
using the ▼▲ buttons select from sAe, en, iec or din. Press the enter button to confirm selection.
4.12.6.
the display will now prompt you to enter the cold cranking amps of the battery. (set cAPAcitY)
4.12.7.
using the ▼▲ buttons alter the numeric display until it shows the rated cold cranking current (ccA) for the battery.
4.12.8.
the display will now ask if the battery is charged.
4.12.9.
using the ▼▲ buttons select Yes or no then press the enter button and the battery test will begin.
4.12.10. When the test is complete the display will show the actual voltage and ccA together with one of the following messages:
GOOD & PASS:
GOOD & RECHARGE:
RECHARGE & RETEST:
BAD & REPLACE:
BAD CELL & REPLACE:
4.12.11. Press enter button to return to menu to select 'sYstem test' or remove the clamps from the battery if no further tests are required.
4.13.
STARTER TEST
4.13.1.
confirm that all electrical items are switched off and that the transmission is in neutral or park and that the parking brake is applied. start
the engine.
4.13.2.
once the engine is running the display will show one of the two following messages.
Cranking volts ....V Normal: Press the enter button to start the charging system test, see 4.14.
Cranking volts ....V Low: troubleshoot the starter and wiring, following the manufacturer's procedure.
© Jack sealey limited
battery oK and ready for use.
battery oK but needs recharging.
recharge battery and then retest.
battery will not hold charge - replace.
battery has faulty cell(s) - replace.
Original Language Version
bt2002.V2| issue:1 30/05/17
Advertisement
