1. Manuals
  2. Brands
  3. Sidchrome Manuals
  4. Power Screwdriver
  5. SCMT90031
  6. Operation and maintenance manual

Sidchrome SCMT90031 Operation And Maintenance Manual

10.8v 10mm (3/8") 2 speed cordless drill
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SCMT90031
Operation and Maintenance Manual
10mm (3/8") SCMT90031
WARNING
To reduce the risk of injury, read and
understand these safety warnings and
instructions before using the tool.
Keep these instructions with the tool
for future reference. If you have any
questions, contact your SIDCHROME
representative or distributor.
10.8V 10mm ( 3/8" ) 2 Speed Cordless Drill
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SCMT90031 and is the answer not in the manual?

Questions and answers

Summary of Contents for Sidchrome SCMT90031

  • Page 1 SCMT90031 Operation and Maintenance Manual 10mm (3/8") SCMT90031 WARNING To reduce the risk of injury, read and understand these safety warnings and instructions before using the tool. Keep these instructions with the tool for future reference. If you have any questions, contact your SIDCHROME representative or distributor.

  • Page 2: General Power Tool Safety Warnings

    WARNING Definitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
  • Page 3 c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on.

  • Page 4: Important Safety Instructions For All Battery Packs

    Hold power tool by insulated gripping surfaces when performing an operation where the fastener may contact • hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. Use clamps or other practical way to secure and support the workpiece to a stable platform.

  • Page 5: Important Safety Instructions For All Battery Chargers

    WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock may result. CAUTION: Burn hazard. To reduce the risk of injury, charge only Sidchrome rechargeable batteries. Other types of batteries may burst causing personal injury and damage.
  • Page 6 • Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire, electric shock, or electrocution. • When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
  • Page 7 Additional Important Safety Instructions for all Battery Packs Battery type The SCMT90031 operates on 10.8 volt battery pack. The SCMT90050 battery pack may be used. Refer to technical data for more information. Storage Recommendations 1. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold. For optimum battery performance and life, store battery packs at room temperature when not in use.
  • Page 8 Do not charge damaged battery packs Labels on Charger and Battery Pack Use only with SIDCHROME battery packs. other may burst causing personal injury and Read instruction manual before damage. Do not expose to water. Battery charging Have defective cords replaced immediately.

  • Page 9: Electrical Safety

    Also make sure that the voltage of your charger corresponds to that of your mains. Your Sidchrome charger is double insulated in accordance with EN 60335; therefore no earth is required. If the supply cord is damaged, it must be replaced by a specially prepared cord available through the Sidchrome service organization. Using an extension cable An extension cord should not be used unless absolutely necessary.
  • Page 10 Forward/Reverse Control Button (Fig. 2) A forward/reverse control button (B) determines the direction of the tool and also serves as a lock off button. To select forward rotation, release the trigger switch and depress the forward/reverse control button on the right side of the tool. To select reverse, depress the forward/reverse control button on the left side of the tool.
  • Page 11 Chuck Installation (Fig. 7) Screw the chuck on by hand as far as it will go and insert screw (lefthand thread). Tighten screw securely. Tighten the chuck around the shorter end of a 1/4” (6.4 mm) or larger hex key (not supplied) strike the longer end in the clockwise direction with a wooden mallet, as shown.

  • Page 12: Specifications

    15.88 mm (5/8”) Maintenance Your Sidchrome power tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. WARNING: To reduce the risk of serious personal injury, place the forward/reverse button in the lock-off position or turn tool off and disconnect battery pack before making any adjustments or removing/installing attachments or accessories.

  • Page 13: Protecting The Environment

    WARNING: Since accessories, other than those offered by Sidchrome, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only Sidchrome-recommended accessories should be used with this product.
  • Page 14 SCMT90050 SCMT90061...
  • Page 16 SIDCHROME 82 TARYN DRIVE EPPING VICTORIA 3076 AUSTRALIA Customer Service Phone Number 1 800 338 002 Copyright © 2014 SIDCHROME Manual #N256181...

Table of Contents