Table of Contents
Advertisement
Quick Links
INSTALLATION HANDBOOK
18v CRIMPING TOOL
SafetyLink is an innovative
anchor company achieving
success and keeping you safe
whilst working at heights.
Read entire handbook before installing SafetyLink products. All products must be installed in accordance
with SafetyLink's installation handbook, using only products supplied by SafetyLink Pty Ltd. Failure to
follow all warnings and instructions may result in a serious injury or death.
SafetyLink Pty Ltd
AU: 1300 789 545
INT: +61 2 4964 1068
i nfo@saf et yl i nk.com
www.safetylink.com
ROOF ANCHORS
HORIZONTAL LIFELINES
PERMANENT LADDERS
LADDER STABILIZERS
TEMPORARY ANCHOR
Advertisement
Table of Contents
Summary of Contents for Safety Link EPB-4201
- Page 1 INSTALLATION HANDBOOK 18v CRIMPING TOOL ROOF ANCHORS SafetyLink is an innovative HORIZONTAL LIFELINES anchor company achieving PERMANENT LADDERS success and keeping you safe LADDER STABILIZERS whilst working at heights. TEMPORARY ANCHOR Read entire handbook before installing SafetyLink products. All products must be installed in accordance with SafetyLink’s installation handbook, using only products supplied by SafetyLink Pty Ltd.
-
Page 2: Table Of Contents
TABLE OF CONTENTS SafetyLink Crimping Tool WARRANTIES ........................ 4 CRIMPING TOOL - SPECIFICATION ................5 CRIMPING TOOL – PRIOR TO USE ................. 6 CRIMPING TOOL – OPERATING/USE................6 CRIMPING TOOL – OPERATING/USE................8 MAINTENANCE GUIDE – CRIMPING TOOL ..............9 STORAGE ........................ -
Page 3: Warranties
WARRANTIES EXTRACT: SafetyLink Pty Ltd STANDARD TERMS AND CONDITIONS 11.1 To the extent permitted by law all implied conditions, warranties and undertakings are expressly excluded. 11.2 Except as provided in this clause the Company shall not be liable for any loss or damage, whether direct or indirect (including consequential losses or damage) arising out of any breach of contract by the Company or any negligence of the Company, its employees or agents. -
Page 4: Crimping Tool - Specification
CRIMPING TOOL - SPECIFICATION SPECIFICATION DIE NO. MODEL NO. EPB-4201 NC3035 CU35 OUTPUT 12 TONS NC3050 CU50 VOLTAGE DC 18V NC3070 CU70 WEIGHT 7.3 KGS NC3095 CU95 NC30120 CU120 460mm(L) DIMENSION 70mm(W) NC30150 CU150 240mm(C) NC30185 CU185 OPENING(D) 42mm NC30240... -
Page 5: Crimping Tool - Prior To Use
CRIMPING TOOL – PRIOR TO USE • Please wear protective equipment while operating to ensure your safety. Warning: This tool is not insulated. • Check the crimping range and suitable crimping material. • Check your crimping material is suitable for this tool and your crimping material is in the range of EPB SERIES TOOLS. - Page 6 CRIMPING TOOL – OPERATING/USE Insert the battery to CRIMPER as below picture 1: • Battery will be buckled to the tool Picture 1: Set battery Follow four steps as below picture 2 to insert the dies: 1/ Pull out Fixed Ring and put the dies in. 2/ Push the Fixed Ring as narrow direction.
-
Page 7: Crimping Tool - Operating/Use
CRIMPING TOOL – OPERATING/USE After setting the dies, crimping material and battery, please press the Switch and Oil Return to operate the crimping dies to crimp, as below picture 3: Picture 3: Operation Return to Table of Contents Ref: Crimping_Tool_18v_Handbook Page 7 of 16 Doc ID: MKT-567 Version: 2.0... -
Page 8: Maintenance Guide - Crimping Tool
MAINTENANCE GUIDE – CRIMPING TOOL STORAGE The hydraulic oil for EPB-4201: Add/use hydraulic oil SHELL TELLUS T-15 or SEA#20. Do not use other brands. Otherwise the tool will be damaged. STORAGE Put the tool, charger and battery in a dry clean place. Please charge the battery fully once every two months to make sure the battery has longer life. -
Page 9: Crimping Tool - 18V Battery & Charger Set
CRIMPING TOOL - 18V BATTERY & CHARGER SET HOW TO OPERATE/USE CH-07 CHARGER • The charger CH-07 is suitable for Li-Ion battery B-04(3Ah) & B-06(1.5Ah). The voltage of charger CH- 07 is 18V. • While connecting to power, the digital monitor shows . -
Page 10: Crimping Tool - 18V Battery & Charger Set
CRIMPING TOOL - 18V BATTERY & CHARGER SET ABOUT THE 18V LI-ION BATTERY: B-04 & B-06 B-04(3.0Ah) SPECIFICATION MODEL NO. B-04 VOLTAGE WEIGHT 0.6 KG DIMENSION 122mm(L)x75mm(W)x69mm(H) CHARGING TIME 60-70 MINUTES CAPACITY 3.0Ah MEMORY EFFECT B-06(1.5Ah) SPECIFICATION MODEL NO. B-06 VOLTAGE WEIGHT 0.3 KG... -
Page 11: Crimping Tool - 18V Battery & Charger Set
CRIMPING TOOL - 18V BATTERY & CHARGER SET MANUAL/INSTRUCTION OF BATTERY SPECIFICATION Voltage 9.6V 14.4V CURRENT CHARGING Ni-MH B-03 B-02 3.0Ah 90 MIN. LI-ION B-05 B-04 3.0Ah 60 MIN. B-06 1.5Ah 30 MIN. BEFORE OPERATION PLEASE NOTE ◆ Do not contact the battery terminals with any metal. Otherwise the battery may short circuit. ◆... -
Page 12: Example: Layout Of Lifeline System
EXAMPLE: LAYOUT OF LIFELINE SYSTEM All working at heights safety procedures must be complied with when installing SafetyLink height safety systems. For more information refer to your state or territories current legislation, regulations, policies and codes of practices. Horizontal height safety lifelines must only be installed and used by competent people with relevant current height safety qualifications. -
Page 13: Appendix A - Crimped Fittings
APPENDIX A – CRIMPED FITTINGS 1. Insert the cable into the open end of the fitting to be swaged, mark the cable where the cable and the fitting meet. Remove the cable and check that the mark is at least 84mm from the cable end. 2. -
Page 14: Notes
NOTES Return to Table of Contents Ref: Crimping_Tool_18v_Handbook Page 14 of 16 Doc ID: MKT-567 Version: 2.0... -
Page 15: Notes
NOTES Return to Table of Contents Ref: Crimping_Tool_18v_Handbook Page 15 of 16 Doc ID: MKT-567 Version: 2.0... -
Page 16: In Case Of Accident
IN CASE OF ACCIDENT A FALL RESCUE PLAN AND SAFE WORK STATEMENT MUST BE DEVELOPED PRIOR TO USING SAFETYLINK SYSTEMS AND EQUIPMENT. PERSONS WORKING AT HEIGHTS SHOULD NOT WORK ALONE. It is critical that before using any SafetyLink Systems a fall rescue plan is in place for any persons suspended mid-air following a fall.