Subscribe to Our Youtube Channel
Summary of Contents for Tornado TP200-Q02-U
- Page 1 Operations and Maintenance Manual For Commercial Use Only PORTABLE BATTERY POWERED MISTER Model No. TP200-Q02-U SAVE THESE INSTRUCTIONS Form No. T-OMPBM 12/2020 ©Tornado Industries, LLC. All right reserved. T-OMPBM 12/2020...
- Page 2 Your new Tornado unit is a high quality, precision-made product. All parts used in the manufacturing of this unit have passed rigid quality control standards prior to assembly. Please safeguard the original receipt/invoice given at the time of purchase. If you...
- Page 3 Within 30 days of purchase, to activate product warranty, go to: https://tornadovac.com/services/warranty-registration-form.aspx For warranty information go to www.tornadovac.com Prior to operating the Portable Battery Powered Mister, read and understand completely this owner’s manual paying special attention to warning labels. These labels indicate a potentially hazardous situation that could result in death or serious injury if not avoided.
- Page 4 TP200-Q02-U Specifications Pressure (Max.) 130 PSI / 9 BAR Weight (Empty) 3.9 LBS / 1.8 KG Weight (Full of Solution) ≥7.5 LBS / 3.4 KG Dimensions (HxWxL) 12” x 4” x 8” / 305 x 102 x 203 mm Voltage 10.8 VDC...
-
Page 5: Important Safety Instructions
1. IMPORTANT SAFETY INSTRUCTIONS Read and understand this owner’s manual and all labels on the unit before operating. Safety is a combination of common sense, staying alert, and knowing how your unit works. To reduce the risk of personal injury or damage to your unit use only as indicated in this manual. - Page 6 1. IMPORTANT SAFETY INSTRUCTIONS Pressurized Equipment Warning Unit is under high pressure when machine is activated. If leaks are visible around coiled hose connections, replace hose immediately with part number shown in this manual. If pump continues to run when the trigger is not depressed, turn machine OFF, discontinue use and return to an authorized service center.
-
Page 7: Box Contents
2. BOX CONTENTS Upon initial receipt of unit, open box and ensure all parts are included as shown below: 2. Coiled Hose 1. Wand Assembly 3. Mister Assembly 4. Strap Assembly 5. Battery 7. Battery Charger 6. Owner’s Manual T-OMPBM 12/2020... -
Page 8: Initial Assembly
3. OPERATING INSTRUCTIONS A. Initial Assembly 1. Remove all contents from box and ensure all components are present per the BOX CONTENTS section of this manual 2. Firmly attach one end of hose to the wand assembly and the other end to the machine ensuring the hose is fully inserted (Fig 1). -
Page 9: Operation
3. OPERATING INSTRUCTIONS D. Operation Prior to filling tank, remove battery from unit and place away from wet area. 1. Remove cap from tank. 2. Pour the recommended amount of disinfectant into the ½ gallon tank and fill about ¼ of the way fill with clean water. Replace cap and gently shake contents to mix disinfectant with water. -
Page 10: After Use
3. OPERATING INSTRUCTIONS E. After use Upon completion of disinfection, empty contents of tank into an approved storage container. Add ¼ gallon (half full) of clean water to the tank and replace cap. Turn unit ON, pull spray trigger, and allow clean water to flush through system, making sure to follow proper disposal of the water being flushed through the system as there will be residual chemical found in the spray (Follow chemical manufacturer’s recommendation for disposal). - Page 11 3. OPERATING INSTRUCTIONS F. Troubleshooting Occasionally air may enter the system and can cause a vacuum lock. This is indicated by a greatly reduced flow of liquid out of the end of the wand. Follow the steps below to correct. Turn machine OFF.
- Page 12 4. ASSEMBLY INSTRUCTIONS Figure 1 Push hose FULLY into fitting. Once fitting bottoms out, tug on tubing to ensure snug fit. Figure 2 T-OMPBM 12/2020...
-
Page 13: Battery Installation
5. BATTERY INSTALLATION Figure 3 Battery Port Press on both sides To remove battery at the same time. Figure 4 T-OMPBM 12/2020... - Page 14 6. SPRAY TIP REPLACEMENT The spray tip is made of plastic and will therefore require replacement over time. Use only the replacement tip listed in the parts section of this Figure 3 manual. 1/2" 9/16" REMOVE Figure 4 INSTALL – USE THREAD SEALER T-OMPBM 12/2020...
-
Page 15: Key Features
7. KEY FEATURES PADDED SHOULDER STRAP WITH QUICK DISCONNECTS 10’ COILED PRESSURE HOSE VACUUM RELIEF VALVE CARRY HANDLE POWER SWITCH TRIGGER 10.8V LITHIUM-ION NOZZLE EXTENSION BATTERY AND CHARGER NOZZLE SOLUTION LEVEL WINDOW T-OMPBM 12/2020... - Page 16 8. SCHEMATICS Figure 3 T-OMPBM 12/2020...
-
Page 17: Parts List
X2250 Clamp, Hose, ¼” X2229 Pear Link X2260 Label, Attention, Clean After Use X2201 Shell, Right X2234 Label, Tornado Branding X2261 Label, Power Off to Install Battery A328-1500 On/Off Switch X2224 Anti Slip Pad w/HD Adhesive X2203 Housing, Battery X2259 Lead Wire, Power Screw, 8-32 X 5/8”... - Page 18 9. PARTS LIST ITEM NO. PART NUMBER DESCRIPTION X2258 Cap, Solution Bottle (Aftermarket Part) X2202 Bottle, Fluid + Caps and Seals X2200 Shell, Left A732-8414 Screw, 8-18 HI-LO X2207 Battery, Lithium Ion, 10.8V X2208 Charger, Lithium-Ion Battery, Input 100-240V, Output 12V DC 1.5A with US AC Cable X2206 Strap, Carry...
- Page 19 10. NOTES 1. ____________________________________________ 2. ____________________________________________ 3. ____________________________________________ 4. ____________________________________________ 5. ____________________________________________ 6. ____________________________________________ 7. ____________________________________________ 8. ____________________________________________ 9. ____________________________________________ 10. ____________________________________________ T-OMPBM 12/2020...
- Page 20 Figure 3 Tornado Industries, LLC 3101 Wichita Court Ft. Worth, TX 76140-1755 Phone: 800-VACUUMS Fax: 1-817-551-0719 WWW.TORNADOVAC.COM Record of Purchase Serial Number: Purchase Date: Dealer: Phone Number T-OMPBM 12/2020...
Need help?
Do you have a question about the TP200-Q02-U and is the answer not in the manual?
Questions and answers