Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for X-GLOO XC Series
Summary of Contents for X-GLOO XC Series
- Page 1 ENGLISH USER MANUAL XC / XG-SERIES INFLATABLE EVENT TENTS...
- Page 2 THANK YOU FOR YOUR TRUST Skywalk GmbH & Co. KG congratulates you on the pur- chase of your inflatable X GLOO Event Tent, the modular, lightweight tent system without compressors and poles. In order to guarantee the perfect operation, optimal function, long product life and your personal safety and the safety of your guests, please note the following: Before you use your Inflatable Event Tent for the first...
-
Page 3: Table Of Contents
TECHNICAL DATA STANDARD DELIVERY HAZARD AND SAFETY INFORMATION SET UP ANCHORING Anchoring with Tube Ballasts Anchoring with Water Ballast Barrels Anchoring with the Anchoring Set Proper use of the Anchoring Lines/Webbing Securing the Walls with Wall Ballasts OPTIONAL COMPONENTS Walls Tunnel Part Canopy and Canopy Banner Roof Banner... -
Page 4: Technical Data
TECHNICAL DATA Tube diameter XC 3 XG 4 XG 5 XG 6 XG 8 Exterior side length 3,0 m 4,0 m 5,0 m 6,0 m 7,85 m Entrance height 1,95 m 2,0 m 2,5 m 3,0 m 3,94 m Total height 2,6 m 2,38 m 3,0 m... -
Page 5: Standard Delivery
STANDARD DELIVERY XC 3 Multifunction transport bag (1) Hand pump (2) Anchoring line set (3) User manual and quick user guide (4) Replacement bladder (9) XG 4 | XG 5 | XG 6 Multifunction transport bag (1) Hand pump (2) Anchoring line set (3) User manual and quick user guide (4) -
Page 6: Hazard And Safety Information
HAZARD AND SAFETY INFORMATION CAUTION: The X GLOO XG cess. This will help keep the infla- series and the XC3 have been table bladder inside the Tube in developed to serve as mobile the correct position, assuring pre- and modular lightweight tents. per and complete inflation and Despite their low weight and stability. - Page 7 OPERATION - On tarmac or similarly-hard ground surfaces the tents must • The inflatable X GLOO Event Tent be sufficiently ballasted (see is not intended for continuous use X GLOO wind certificate). and should be inspected for wear 2) Additionally, you must use an- or damage after every event.
- Page 8 - CPAI 84-95, Section 6 Specifica- - If the damage to the bladder is tion of the American Association visible and the length of dama- of Sailcloth Materials for the as- ge is smaller than 1 cm, then ap- sessment of flame-retardant ply the adhesive repair patch materials used in (event-) tents.
- Page 9 MATERIALS care with the Window Walls in low temperatures and pack them ca- • All of the materials currently imple- refully. mented in the inflatable X GLOO • Never store the Event Tent in an Event Tent have been subjected automobile in direct sunlight.
-
Page 10: Set Up
SET UP 1 LAY OUT THE TENT Spread out the Event Tent in the area intended for set up. Try to make sure that the Tube ends are positioned approximately where you want them once the tent is inflated. This way you can avoid having to reposition or handle the tent again. - Page 11 2 PREPARE THE VALVES The valve consists of the socket ring, (1) which is attached to the bladder, and a screw-on housing (2) with attached protective cap (3). The housing must be tightened securely to the socket ring before inflation (4). The backstroke valve inside the hou- sing prevents air from escaping.
- Page 12 3 INFLATE 3.1 Connect the hose to the pump and then insert the other end of the hose into the valve on one of the Tubes. 3.2 First inflate two Tubes opposite one another to form a 180° semicircle (a). 3.3 Next inflate the Tube laying on top of and between the two inflated Tubes.
- Page 13 SETUP USING THE INFLATING WITH THE HAND PUMP PROTECTION FOIL The Hand Pump included in the standard delivery is equipped with different valve adapters and an air hose. Follow these instructions if using Do not kink or press down on the air hose to avoid air our optional Protection Foil to help leakage or damage! prevent soiling or damaging your...
-
Page 14: Anchoring
ANCHORING ANCHORING WITH TUBE BALLASTS (WATER OR SAND) Each Tube Ballast Set includes four ballasts. The bal- lasts can be filled with water or sand/gravel and then connected to the inside or the outside of the tent Tubes by using the two clips on each ballast. Filling with water Open the velcro on the ballast cover and pull out the inner water bladder until the fill valve is visible (a). -
Page 15: Anchoring With Water Ballast Barrels
ANCHORING WITH WATER BALLAST BARRELS The Water Ballast Barrels can be used as anchors for your inflatable X GLOO Event Tent, as seating, or as both. To fill Open the two valve covers on the Ballast Barrel. Make sure that the check valve at the bottom of the Barrel is closed so that no water or air can escape when filling (a). -
Page 16: Anchoring With The Anchoring Set
ANCHORING WITH THE TENT STAKES ANCHORING SET/TENT STAKES for the XC 3 / XG 4 Tent Stakes Qty. CAUTION: The number of anchors required 300 mm L 16 pc. inner Tube + Walls depends on the size of the tent and the wind condi- 500 mm L 4 pc. -
Page 17: Securing The Walls With Wall Ballasts
SECURING THE WALLS WITH WALL BALLASTS (WATER OR SAND) Each Wall Ballast can be filled with water or sand/gra- vel and then connected to the Wall using the attached toggles (c). Filling with water Open the velcro on the ballast cover and pull out the inner water bladder until the fill valve is visible. -
Page 18: Optional Components
OPTIONAL COMPONENTS WALLS The walls are available in four variations: as Standard Walls (completely closed), Window Walls, Entrance Walls, and Double-Sided Standard Walls. The zippers attach on the right and left of the Tent Roof and meet together at the top. PLEASE NOTE: Walls can be installed with the side of your choice facing outward. - Page 19 Opening and securing the Entrance Wall The Entrance Wall is zipped on as described on page 18. To hold the Entrance Wall open, open the zipper in the middle of the Wall and gather each side together. On each side of the Entrance Wall you will find a toggle on a length of cord.
-
Page 20: Tunnel Part
TUNNEL PART The Tunnel Part makes it possible to connect two infla- table X GLOO Event Tents to one another. Tunnel Parts are available for connecting Event Tents of different sizes, and for connecting Event Tents of the same size. The Tunnel Part is zipped on between the Tents in place of a Side Wall (a). -
Page 21: Led Lighting Kit
LED LIGHTING KIT Hanging the LED Lighting Kit in your inflatable X GLOO Event Tent It is easiest to install the LED Lighting Kit during the setup of your Event Tent, just after inflating three of the four Tubes. Take the long end of webbing con- nected to the LED light and loop it above the tube intersection (a). -
Page 22: Takedown
TAKEDOWN Make sure that all of the tent stakes are removed and all anchoring lines are released before deflating the Tubes on your Event Tent. Remove all optional components (e.g. Walls, Canopy, etc) which are attached to the Event Tent. Next, open the overpressure valve on each Tube (a). -
Page 23: Cleaning
CLEANING Dirt and stains should be removed without the use of soap or water whenever possible. We recommend using a soft, dry brush or microfiber cloth. If the stain cannot be brushed away, then use a small amount of conven- tional soap mixed with lots of water. -
Page 24: Repair
REPAIR BLADDER REPAIR Adhesive repair patch Our adhesive repair patch (70 x 50 mm) resists perfora- tion, is stretch-durable and has been developed espe- cially for repair of tears and holes in the bladder. • High adhesion guarantees impermeability • Resistant to UV exposure •... -
Page 25: Removing The Roof
REPAIR XG SERIES (XG 4-8) The Event Tent can be easily disassembled into indivi- dual parts (Roof and Tubes) for repair or replacement. Re-attaching the new or repaired part is just as easy. REMOVING THE ROOF Under the Roof at each Tube end you will find two velcro straps fixing the tent Roof to the Tube. -
Page 26: Bladder Replacement
BLADDER REPLACEMENT Lay out the Event Tent neatly so that the damaged Tube is on top and the service zipper is fa- cing upwards. Open the two velcro straps at the top of the Tube (a). Open the service zipper at the top of the Tube (b). - Page 27 12 Now, starting from the bladder sack at the opposite end, thread the Tube completely onto your arm. Grasp the end of the repla- cement bladder through the up- per bladder sack (k). Pull the re- placement bladder carefully into the Tube. CAUTION: Make sure that the replacement bladder does not get twisted when pulling...
- Page 28 18 Fold the bladder sack in half, pressing it firmly to close the long velcro strap in the middle (q). 19 Loop the three velcro straps through the corresponding plas- tic buckles on the bladder sack, and then press each one firmly to close it (r).
-
Page 29: Removing The Roof | Xc
REPAIR XC 3 The XC 3-model Event Tent can be easily disassembled into individual parts (Roof and Tubes) for repair or re- placement. Re-attaching the new or repaired part is just as easy. REMOVING THE ROOF Unhook the plastic toggle from the loop at the end of each Tube (a). -
Page 30: Bladder Replacement | Xc
BLADDER REPLACEMENT Lay out the Event Tent neatly so that the damaged Tube is on top and the service zipper is ea- sily accessible. Open the velcro straps at the top of the Tube that connect it to the neighboring Tubes (a). Open the service zipper at the top of the Tube (b). - Page 31 11 Carefully pull the replacement bladder into the Tube until it extends slightly out of both ser- vice openings (k). CAUTION: When pulling the replacement bladder into the Tube, please make sure that it does not become twisted. It can help to have a second person to help guide the replacement bladder for this purpose.
Need help?
Do you have a question about the XC Series and is the answer not in the manual?
Questions and answers