Sealey SA800.V3 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
! WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
! WARNING! Disconnect from air supply (and dust-free system if connected) before changing accessories, servicing or carrying out
maintenance.
# Maintain the sander in good condition (use an authorised service agent).
# Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
# Use the sander in a suitable work area and keep area clean, tidy and free from unrelated materials. Ensure that there is adequate lighting.
# Before each use check abrasive disc for condition. If worn or damaged replace immediately.
! WARNING! Always wear approved eye or face protection when operating the sander.
# If dust is generated, use face, dust or respiratory protection in accordance with COSHH regulations.
# Depending on the task, sander noise level may exceed 85dB, in which case wear safety ear defenders.
# Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
# Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
# Keep children and unauthorised persons away from the working area.
# Ensure the workpiece is correctly secured before operating the sander. Never hold workpiece by hand.
# Check the workpiece to ensure there are no protruding nails, screws, stones, etc.
# Avoid unintentional starting.
! WARNING! Ensure that the correct air pressure is maintained and not exceeded.
# Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
# Prolonged exposure to vibration from these tools poses a health risk. It is the owner's responsibility to correctly
assess the potential hazard, issue guidelines for safe periods of use and offer suitable protective equipment.
$ DO NOT use the sander for a task it is not designed to perform.
$ DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
! WARNING! DO NOT cut, grind, saw or sand any materials containing asbestos.
$ DO NOT carry the sander by the hose, or yank the hose from the air supply.
$ DO NOT get the sander wet or use in damp or wet locations.
$ DO NOT use the sander with water. These models are dry sanders only.
$ DO NOT operate sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
$ DO NOT leave the sander operating unattended.
$ DO NOT carry the sander with your hand on the power lever.
$ DO NOT direct air from the air hose at yourself or others.
# When not in use disconnect from air supply (and dust-free system if connected) and store in a safe, dry, childproof location.
! WARNING! LEAD PAINT. Paint once contained lead as a traditional ingredient. Contact with the toxic dust from the removal of such paint
must therefore be avoided. The following action must be taken before using the sander on a surface that you suspect may contain lead paint.
1. User must determine potential hazard relating to age of paint to be removed (modern paints do not have lead content).
2. DANGER! Keep all persons and pets away from the work area. The following are particularly vulnerable to the effects of lead paint
dust: Pregnant women, babies and children.
3. We recommend personal protection by using the following safety items:
a) Paint Spray Respirator (Our ref SSP16EN).
b) PE Coated Hooded Coverall (Our ref SSP266).
c) Latex Gloves (Our ref SSP24).
4. Take adequate measures to contain the paint dust, flakes and scrapings.
5. Continue to wear safety equipment (3) and thoroughly clean all areas when task is complete.
6. Seal paint waste in bags or containers for disposal according to local regulations.
Risk of Hand Arm Vibration Injury
Air Operated Sanders, models SA800.V3 & SA801.V3, when operated in accordance with these instructions and tested in accordance with
EN 28662-2: 1994 results in the following vibration emission declared in accordance with BS EN12096: 1996.
Measured vibration emission value: . . . . . .1.9m/s
Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . .0.76m/s
These values are suitable for comparison with emission levels of other tools that have been subject to the same test. This tool may
cause hand-arm vibration syndrome if its use is inadequately managed.
Recommended Measures to reduce risk of hand-arm vibration syndrome:
This item represents a low Hand-Arm Vibration risk to users. The calculated maximum usage period exceeds 8 hours. We recommend
appropriate safety equipment is utilised and regular breaks for the operator are employed to reduce any residual risk of fatigue or repetitive
strain injury.
INSTRUCTIONS FOR:
AIR OPERATED PALM SANDERS
MODELS: SA800.V3 AND SA801.V3
2
2
SA800.V3, SA801.V3 - 1 - 020806