Auvi WIP20S Supplementary Manual

Designed
for
Skype
™
Copyright/Trademarks
© 2005 Auvi Technologies, LLC. All rights reserved.
Auvi Technologies "Auvi" shall not be liable for any errors contained herein or
for any damages arising out of or related to this document or the information
contained herein, even if Auvi has been advised of the possibility of such
damages. This document is intended for informational and instructional
purposes only. Auvi reserves the right to make changes in the specifications
and other information contained in this document without prior notification.
Auvi disclaims any obligation to update the information contained herein.
Auvi Technologies, Auvi design and Vision Beyond Sound are trademarks or
registered trademarks of Auvi Technologies LLC in the United States and/or
other countries. Windows is a trademark or registered trademark of Microsoft
Corporation in the United States and/or other countries. Skype is a trademark
or registered trademark of Skype Technologies S.A. in the United States
and/or other countries. TeleVoce and TeleVoce logo are trademarks or
registered trademarks of TeleVoce, Inc. in the United States and/or other
countries.
All other product names may be trademarks of the companies with which they
are associated.
Auvi Technologies For customer inquiries:
custservice@auviusa.com
5988 Mid Rivers Mall Drive
St. Charles, MO 63304 636-447-4005
World Wide Web address:
http://www.auviworld.com
http://www.auvivoip.com
WIP20
WIP20S
Regulatory Compliance Notices
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna;
• Increase the separation between the equipment and receiver;
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected;
• Consult the dealer or an experience radio/TV technician for help.
The FCC requires the users to be notified that any changes or modifications
made to this device that are not expressly approved by the party responsible
for compliance may void the user's authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Under the environment with radio frequency interference, the sample may
generate a tone and resume to normal operation when the interference stops.
Printed in China The unit may generate a tone when there is radio interference appeared on the
power lines. The unit will revert to normal operation when the interference stops.
Connect telephone cord
Phone
cord
Standard phone WIP20
Power in
Audio in
MIC / SPKR
cables
Computer
Regulatory Compliance Notices
Warning: To reduce risk of electric shock, do not directly or indirectly (through
a phone) connect the device to a PSTN wall outlet.
Troubleshooting
Skype™ is running but I do not hear a dial-tone - Adjust the speaker sound level
and make sure the Auvi Interface application is running.
When listening to music through the audio out jack, I hear music when I
answer an incoming call - Turn off or pause the music program you are using.
The person on the other end of the conversation cannot hear me - Open up
the mic sound level and make sure that the mic is not on mute. If you have multiple
mic-in jacks make sure that the correct one is connected to the WIP20.
For additional troubleshooting issues and Frequently Asked Questions on the
WIP20, visit the Support page at www.auvivoip.com.
For Skype™ software inquiries, visit www.skype.com.
System Requirements
• Windows® XP only
• Pentium MMX® 400MHz or higher
• CD disk drive
• 128MB minimum RAM
• 5MB free space minimum on hard drive
• Available microphone and speaker audio jacks
• Analog traditional or cordless telephone with DTMF tone dialing feature
• Broadband or dial-up Internet connection
Mic in
Audio out
Internet