Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Butts of Bawtry Manuals
  4. Spreader
  5. SP80WB
  6. Instruction manual

Butts of Bawtry SP80WB Instruction Manual

36kg/80lb walk behind spreader
Hide thumbs

Advertisement

Quick Links

Download this manual
36KG / 80LB WALK BEHIND SPREADER
SP80WB
INSTRUCTION MANUAL
1

Advertisement

loading

Related Manuals for Butts of Bawtry SP80WB

Summary of Contents for Butts of Bawtry SP80WB

  • Page 1 36KG / 80LB WALK BEHIND SPREADER SP80WB INSTRUCTION MANUAL...
  • Page 2 SAVE THESE INSTRUCTIONS AND PRECAUTIONS. READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE. 1. HELPFUL HINTS: READ THE INSTRUCTIONS BEFORE ASSEMBLY  If your spreader does not spread evenly, be sure the FRONT on the gear box points to the front of the spreader. The impeller must turn clockwise. Reversing the gear box will cause the impeller to turn counter clockwise.
  • Page 3 STEP 1: Install impeller onto the Gear Box & Axle Assembly. Insert Screw M4x20 through impeller then through Gear Box Axle.
  • Page 4 STEP 2: Attach the Wheel Assembly Frame on each side of the Gear Box Axle and Fixing Connecting Rod, insert two bolts M6x40 into the Fixing Connecting Rod through Wheel Assembly Frame. Make sure the hole on Axle of Gear Box is on the right side when assembly as shown.
  • Page 5 nuts M6 and Big Flat Washers Ø6. Note: The bolts and nuts needn't be tightened yet. STEP 3: Insert Inner Axle Bushing into Outer Axle Bushing and make sure they are tight neatly. Install right Wheel Assembly to right Axle using bolt M5x45 and lock nut M5, and then install the Cap onto right Axle using a wooden or rubber hammer.
  • Page 6 STEP 4: Insert Upper Handle into the Support Leg and tighten using bolts M6x40 and Lock Nuts M6. NOW GO BACK AND TIGHTEN ALL NUTS AND BOLTS STARTING WITH FIRST STEP. DO NOT OVER TIGHTEN.
  • Page 7 STEP 5: (1) Insert the Steel Wire head of control cable into the small hole on Gauge and Lever Assembly. (2)Release two bolts M5x10 and lock nuts on Press Plate. (3) Put the Plastic Tube into the slot of Press Plate. (4) Tighten two bolts M5x10 and lock nuts again. (5). Insert R Pin.
  • Page 8 STEP 6: ADJUSTMENTS. When you have finished all above steps, and if you find the holes at the bottom of hopper can close and open completely by using the handle. You don't need to do the following steps. If it does not close and open completely, you may...

  • Page 9: Parts Drawing

    need to do the following steps. (1) Release two bolts M5x10 on clamp as shown. (2). Push the handle to the top position, use your hand to adjust the adjustable plate so as to make sure the hole at the bottom of hopper can be closed completely. (3). Push the handle to the lowest position, use your hand to adjust the adjustable plate so as to make sure the hole at the bottom of hopper can be opened completely.

  • Page 11: Parts List

    PARTS LIST Ref# Description Ref# Description Carriage Bolt M6x25 Support Leg External-tooth Washer Ø8 Wheel Assembly Frame(Right) Gauge and Lever Assembly Thin Washer Adjust Handle Pole Pneumatic Wheel Adjust Handle A Flat Washer Ø16 Adjust Handle B Axle End Cover Screw M4x18 Inner Axle Bushing Handle Grip...