Table of Contents
Advertisement
Quick Links
EASTMAN
THE EASTMAN
Bat
Model BAT
CAUTION
Machine Equipped
Sharp Blade
Your new Bat is designed to replace hand held shears for
increased performance and capacity with a minimum of
maintenance and service. Equipped with a 4" high speed
round blade, the Bat will cut even the most difficult to cut
fabric.
TO OPERATE MACHINE
Raise the knife guard up just enough to allow the fabric in
over the pressure foot an make contact with the blade.
Press and hold button to activated ON/OFF switch. If cutter
does not perform properly check battery packs. Be sure the
battery packs are properly charged and installed.
TO SHARPEN KNIFE
Take the machine out of material to be cut. To obtain a fine,
keen edge on the blade, while machine is running press
lightly on sharpener button (63C3-21) with a constant
pressure. Hold for 10 seconds, then release.
Before performing any of the following procedures, make
sure the battery power pack has been removed.
LUBRICATION
Follow this procedure yearly for intermittent use, or every
six months for continuous use. Remove emery wheel
(541C1-22) and wipe away any grit deposits. Apply a light
coat of Eastman Lubriko Grease (242C2) to parts and
reassemble.
779 Washington St., Buffalo, N.Y. 14203-1396 U.S.A. • (716)856-2200 • Fax (716)856-1140 or (716)856-2068
Form C-1583
R
Instructions &
Illustrated Parts List
With
WARNING
Manufacturers of Eastman Cloth Cutting and Cloth Spreading Machines
Website: WWW.EastmanCuts.com
WARNING
Safety glasses must be worn at all times when
operating or servicing this equipment.
KNIFE REPLACEMENT
Remove battery pack from Bat. Lay Bat on its side with knife
facing up. Insert a pin or allen wrench into knife hole. With
Spanner Wrench (954C1-12), turn lock nut (4C1-81) coun-
terclockwise. Remove lock nut. CAREFULLY lift out
WORN SHARP KNIFE and DISCARD WITH CARE. Install
new Eastman knife with bevel facing outward. Reverse
procedure to secure new knife.
EMERY WHEEL REPLACEMENT
Remove battery pack from Bat. With Bat on its side (knife
facing up). Remove knife lock nut and knife. Hold sharpener
bushing (21C5-4) with suitable wrench. Remove sharpener
button (63C3-21) and spring. Sharpening stone and bush-
ing assembly can then be removed from sharpener bracket
(663C1-3). Remove retaining ring from shaft of sharpening
stone and remove stone. To Install, assemble in reverse
order.
OPTIONAL BALL TIP
A ball tip (109C5-1) for cutting loosely woven materials,
additional support and cutting accuracy is optional. To
install ball tip to shear plate (726C1-36) gently push ball tip
in place as illustrated.
®
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for EASTMAN BAT
Summary of Contents for EASTMAN BAT
- Page 1 Safety glasses must be worn at all times when maintenance and service. Equipped with a 4" high speed operating or servicing this equipment. round blade, the Bat will cut even the most difficult to cut fabric. KNIFE REPLACEMENT TO OPERATE MACHINE Remove battery pack from Bat.
- Page 2 90–day warranty period. If Eastman determines that the goods or parts are defective in materials or workmanship, Eastman's sole obliga- tion under this warranty shall be, at Eastman's sole option, to repair or replace the defective goods or parts or to provide to the buyer a credit equal to the portion of the purchase price allocable to the defective goods or parts.
- Page 3 * Indicates Optional Parts To order replacement parts call Customer Service at (716) 856-2200. Please specify model and serial num- ber of machine along with part number, description and quantity of parts in order. ® Form C-1583...
- Page 4 Battery turns power off when you turn out the lights; 3.) Move charger could short circuit causing fire, burns, or damage to the bat- and batteries to a surrounding air temperature between +40 to tery.
Need help?
Do you have a question about the BAT and is the answer not in the manual?
Questions and answers