Related Manuals for Sysgration TPMS TT02
Summary of Contents for Sysgration TPMS TT02
- Page 1 TPMS TT02 User Guide TPMS Trigger Tool TT02 User Guide V0.2 Prepared by: Sysgration Inc. Cooperation Sysgration Confidential...
-
Page 2: Table Of Contents
TPMS TT02 User Guide Outline Button UI: ............................ 3 User Guide: ..........................5 TT02 RS232 command settings ....................14 FW Upgrade Operation Guide ....................20 Upgrade thru USB: ........................20 Upgrade thru Bluetooth (Cellphone): ..................22 Sysgration Confidential... -
Page 3: Button Ui
TPMS TT02 User Guide Button UI: Screen state Power Off Power Main TPMS CHECK TPMS TPMS CHECK Menu (no sensor) CHECK (found sensor) Action (display (searching) Long press Power key Power on Power off Power off Power off Power off... - Page 4 TPMS TT02 User Guide Screen state Settings menu Enter combo FW Upgrade BT upgrade USB upgrade screen RESTORE ABOUT Action box field screen screen (without USB plug in) screen screen Long press Power Power off Power off Power off Power off...
-
Page 5: User Guide
TPMS TT02 User Guide User Guide: Power on: TT02 Screen Display TT02 information for 2 seconds when powering on. Enter MAIN screen Power off: TT02 Screen Note:TT02 Will keep power on if under USB connection. Sysgration Confidential... - Page 6 TPMS TT02 User Guide Trigger Sensor: TT02 Screen Press to make the cursor move to “TPMS CHECK” , then press to enter the Press to trigger sensor “TPMS CHECK” screen. Start searching the sensor as below, or you can...
- Page 7 TPMS TT02 User Guide Pressure / Temperature Units Setting: TT02 Screen Press to make the cursor move to Press to make the cursor move to “SETTINGS” , then press to enter the “UNITS” , then press to enter the “UNITS”...
- Page 8 TPMS TT02 User Guide Backlight On/Off Setting: TT02 Screen Press to make the cursor move to Press to make the cursor move to “BACKLIGHT”, then press to enter the “SETTINGS”, then press to enter the “SETTINGS” menu. “BACKLIGHT” item.
- Page 9 TPMS TT02 User Guide USB Port Working Mode Setting (USB HID/ UART): TT02 Screen ※Check if the USB is plugged out. Press to make the cursor move to Press to make the cursor move to “USB MODE” , then press to enter “USB...
- Page 10 TPMS TT02 User Guide TPMS Low Battery Alert: TT02 Screen Press to make the cursor move to Press to make the cursor move to “TPMS LB”, then press to enter the “TPMS “SETTINGS”, then press to enter the LB” item: “SETTINGS”...
- Page 11 TPMS TT02 User Guide FW Upgarde – Thru USB: TT02 Screen Press to make the cursor move to Press to make the cursor move to “SETTINGS”, then press to enter the “FW UPGARDE”, then press to enter “FW “SETTINGS” menu.
- Page 12 TPMS TT02 User Guide Restore: TT02 Screen Press to make the cursor move to Press to make the cursor move to “SETTINGS”, then press to enter the “RESTORE”, then press to enter the “SETTINGS” menu. “RESTORE” item: (1) Press to reset to the default setting then it will exit “RESTORE”...
- Page 13 TPMS TT02 User Guide USB Charging: TT02 Screen The icon in the red box as below display that TT02 is in charging status: Sysgration Confidential...
-
Page 14: Tt02 Rs232 Command Settings
TPMS TT02 User Guide TT02 RS232 command settings UART Setting: Baud rate 19200, Data bit 8, Stop bit 1, No Parity, ASCII Activate Trigger 1. Activate by Button: If Success: TT02 --> COMPUTER: "BBBBBBBBBBBB” 12 bytes, BBBBBBBBBBBB: Bluetooth Address If Fail, TT02 -->... - Page 15 TPMS TT02 User Guide "$TBBBBBBBBBBBBMMMMNNNNRR#" RR: RSSI "$TBBBBBBBBBBBBMMMMNNNNRR#" RSSI Value Ex: RR = 0x64, Receiving RF RSSI = -100 dBm If Fail, TT02 --> COMPUTER: "$TFAIL#" 7 bytes, Stop Trigger COMPUTER --> TT02: "$T0#", 4 bytes Read Last Trigger Result COMPUTER -->...
- Page 16 TPMS TT02 User Guide "$RRBBBBBBBBBBBBMMMMNNNNRR#" RSSI Value Ex: RR = “64”, 0x64 = 100 (Oct), Receiving RF RSSI = -100 dBm If Fail, TT02 --> COMPUTER: "$RRFAIL#" 8 bytes Read Last Trigger Bluetooth Address COMPUTER --> TT02: "$RM#", 4 bytes If Success, TT02 -->...
- Page 17 TPMS TT02 User Guide (2.4 PSI is 17 KPA, 83 KPA (Raw data) - 100 KPA = 17, more than the MIN limit 10KPA , so will display negative character.) If Fail, TT02 --> COMPUTER: "$RPFAIL#" 8 bytes Read Temperature in Fahrenheit for Sensor Format 2 (Advertising) COMPUTER -->...
- Page 18 TPMS TT02 User Guide If Success, TT02 --> COMPUTER: "$RAZVOOOO.O #"12 bytes V = positive/negative characters, ‘-’ or ‘+’ OOOO.O = Z- Acceleration value(Oct) Ex: VOOOO.O = “-0002.5”, Z- Acceleration is -2.5G If Fail, TT02 --> COMPUTER: "$RAZFAIL#" 9 bytes Read Firmware Version COMPUTER -->...
- Page 19 TPMS TT02 User Guide VVVV = Battery voltage (Oct) Ex:VVVV =8315 , TT02 battery voltage is 8315 mV Set Backlight ON/OFF (Test Mode only) COMPUTER --> TT02: "$ZTBKLX#", 8 bytes, $ZTBKLX# = Command Code $ZTBKLX# = Backlight ON or Backlight OFF, “$ZTBKL1#” : ON, “$ZTBKL0#” : OFF If Success, TT02 -->...
-
Page 20: Fw Upgrade Operation Guide
TPMS TT02 User Guide FW Upgrade Operation Guide Upgrade thru USB: 1 Computer needs install Python & nrfutil: 1-1. Download Python (python-2.7.13.msi) and install it to your PC 1-2. Enter the command-line mode of Windows-OS : Please type “cd Python27\Scripts”and press Enter to go to C:\Python27\Scripts>... - Page 21 TPMS TT02 User Guide Note : If you haven’t installed nrfutil-tools in your computer, please go to the section of page 20 about how to install Python & nrfutil for reference. 2-2. Turn on the TT02, confirm it works and...
-
Page 22: Upgrade Thru Bluetooth (Cellphone)
TPMS TT02 User Guide Upgrade thru Bluetooth (Cellphone): 1 How to use Android phone to update the firmware of TT-02 1.1. Please connect your smartphone to the PC, and then copy the TT-02 firmware file to your smartphone. You can create a new folder in your smartphone so that you can easily to find the firmware file. - Page 23 TPMS TT02 User Guide 1.6. Click the DFU icon: Click this icon to enter the DFU process 1.7. Select OTA file type, choose the “ZIP” then click “OK”: 1.8. Select the updated OTA file, click the icon in red box as below if confirm the file is what you...
- Page 24 TPMS TT02 User Guide 1.9. App start to run DFU now, you can see new TT02’s information appeared on App screen which marked with red box, it means TT02 OTA mode is activated, the MAC-Address is also different: Yellow box : Original device Red box: OTA mode active 1.10.
- Page 25 TPMS TT02 User Guide 1.11. It will take a little time to update the OTA firmware, please wait for a while. The message will pop-up to notify when the firmware update is completed: 1.12. Please confirm that your TT-02 has completed the FW update and check your TT-02 can work as well.
- Page 26 TPMS TT02 User Guide This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the TPMS TT02 and is the answer not in the manual?
Questions and answers