Table of Contents
Summary of Contents for Phytec LCD-014
- Page 1 Display Adapter LCD-014 / 017 Hardware Manual Document No.: L-758e_1 Add-on Prod. No.: LCD-014 Add-on PCB. No.: 1337.1 Add-on Prod. No.: LCD-017 Add-on PCB. No.: 1344.0 First Edition A product of a PHYTEC Technology Holding company...
- Page 2 PHYTEC Messtechnik GmbH neither gives any guarantee nor accepts any liability whatsoever for consequential damages resulting from the use of this manual or its associated product. PHYTEC Messtechnik GmbH reserves the right to alter the information contained herein without prior notification and accepts no responsibility for any damages which might result.
-
Page 3: Table Of Contents
List of Tables ....................ii Conventions, Abbreviations and Acronyms..........iii Preface......................v Introduction..................1 1.1 View of LCD-014-x ..............4 1.2 View of LCD-017-x ..............5 1.3 Minimum Requirements to Operate the Display Adapters ..6 1.3.1 PDI Power Supply Connector ......... 6 1.3.2... - Page 4 Figure 4: LCD-014 Physical Dimensions ..........18 Figure 5: LCD-017 Physical Dimensions ..........19 Figure 6: LCD-014 Component Placement, Bottom View ..... 21 Figure 7: LCD-017 Component Placement, Bottom View ..... 22 Figure 8: Preparing Baseboard and Display Adapter......27 Figure 9: Screwing ..................
-
Page 5: Conventions, Abbreviations And Acronyms
Conventions, Abbreviations and Acronyms Conventions, Abbreviations and Acronyms This hardware manual describes the LCD-014-M / LCD-017-xxx PHYTEC Display Adapter. The manual specifies the adapter boards design and function. Precise specifications for the display mounted can be found in the Data Sheet/User's Manual. -
Page 6: Table 1: Abbreviations And Acronyms Used In This Manual
Table 1: Abbreviations and Acronyms used in this Manual Note: The BSPs delivered with PHYTEC Development Kits usually include drivers and/or software for also controlling the PHYTEC Extension Boards. Therefore programming close to hardware at register level is not necessary in most cases. For this reason, this manual contains no information relevant for software development. -
Page 7: Preface
Preface Preface As a member of PHYTEC's new Add-on product family the LCD-014-M / LCD-017-xxx PHYTEC Display Adapter is one of a series of boards that provide additional functions and interfaces to the standard PHYTEC Carrier Boards. Primarily designed PHYTEC’s... - Page 8 Display Adapter LCD-014-x / LCD-017-x Ordering Information LCD-014 is available with the ordering number LCD-014-M and has a 5" VGA display. The part numbering of the model LCD-017 has the following structure: LCD-017-xxxx Display Size / Resolution 035V = 3.5" VGA 050V = 5"...
- Page 9 (particularly in respect to the pin header row connectors, power connector and serial interface to a host-PC). Implementation of PHYTEC products into target devices, as well as user modifications and extensions of PHYTEC products, is subject to renewed establishment of conformity to, and certification of, Electro Magnetic Directives.
- Page 10 Display Adapter LCD-014-x / LCD-017-x viii © PHYTEC Messtechnik GmbH 2011 L-758e_1...
-
Page 11: Introduction
Introduction 1 Introduction The display adapters LCD-014-x and LCD-017-x belong to a series of add-on modules for PHYTEC’s Single Board Computers. These add- on modules allow easy development of complex applications with off- the-shelf components. PHYTEC Display Adapters LCD-014-x and LCD-017-x are compatible to the PHYTEC Display-Interface (PDI) which consists of two universal connectors on the PHYTEC Carrier Board. -
Page 12: Figure 1: Modular Concept Of The Phytec Phycard Development Kit Family
Display Adapter LCD-014-x / LCD-017-x Figure 1: Modular Concept of the PHYTEC phyCARD Development Kit family © PHYTEC Messtechnik GmbH 2011 L-758e_1... - Page 13 • C EEPROM for device recognition (only for x86-systems) • 1-Wire EEPROM for internal use only • Can be mounted on top of an appropriate PHYTEC Carrier Board, or aside with a film hinge © PHYTEC Messtechnik GmbH 2011 L-758e_1...
-
Page 14: 1.1 View Of Lcd-014-X
Display Adapter LCD-014-x / LCD-017-x 1.1 View of LCD-014-x Figure 2: Component side of LDC-014-x © PHYTEC Messtechnik GmbH 2011 L-758e_1... -
Page 15: View Of Lcd-017-X
Introduction View of LCD-017-x Figure 3: Component side of LDC-017-x © PHYTEC Messtechnik GmbH 2011 L-758e_1... -
Page 16: Minimum Requirements To Operate The Display Adapters
Display Adapter LCD-014-x / LCD-017-x Minimum Requirements to Operate the Display Adapters 1.3.1 PDI Power Supply Connector Operation of the display adapters only requires supply of two input voltages (+3.3V with a 1A load and +5V with a 2A load) and the corresponding GND connections. -
Page 17: Connectors
Carrier Board Connectivity (X5, X3) The new concept of using display adapters such as the LCD-014-x and LCD-017-x allows to attach a large number of different displays varying in resolution, signal level, type of the backlight, pinout, etc. to the baseboard using always the same connectors. - Page 18 Note: Text in red indicates signals that are not used on the display adapters LCD-014-x and LCD-017-x. They are included in the PDI specification to provide more functions for a customer designed display adapter or front panel (e.g. an integrated USB connector or power switch).
-
Page 19: Table 2: Display Data Connector Signal Description
Only in case of connecting low-current displays, it might be possible to renounce the Display Power Connector. The PWM signal at pin 10 for controlling the brightness of a display's backlight is generated by an LED dimmer. © PHYTEC Messtechnik GmbH 2011 L-758e_1... -
Page 20: Display Power Connector (X3)
Display Adapter LCD-014-x / LCD-017-x 2.1.2 Display Power Connector (X3) The display power connector X3 (AMP microMatch 8-188275-2) provides all supply voltages needed to supply the display and a backlight. Table 3 shows the pinout with pin names, descriptions and voltages. -
Page 21: Display Connectivity (X2)
LVDS data channel 3 negative input DISP_LVDS_3+ LVDS LVDS data channel 3 positive input Ground Ground Ground GND¹ Ground Table 4: Display connector signal description LCD-014 connects this to shield, but the connected display closes shield with GND © PHYTEC Messtechnik GmbH 2011 L-758e_1... -
Page 22: Touch Screen Connectivity (X1, X16, X17, X18)
Display Adapter LCD-014-x / LCD-017-x Touch Screen Connectivity (X1, X16, X17, X18) LCD-014 only has X1 for connecting the display’s touch. LCD-017 also has X16, X17 and X18 due to the fact, that every touch needs a different type of connector. -
Page 23: Power
Connector X3. It will be converted to the power needed for the backlight. A green LED indicates power presence. Caution: For maximum EMI performance we recommend as a general design rule to connect all GND pins to a solid ground plane. © PHYTEC Messtechnik GmbH 2011 L-758e_1... - Page 24 Display Adapter LCD-014-x / LCD-017-x © PHYTEC Messtechnik GmbH 2011 L-758e_1...
-
Page 25: Components
258mA 104S Table 6: Adjusting output current Ambient Light Photo Sensor Intended to give you the possibility to adjust the brightness of the backlight automatically. C-EEPROM Reserved for further use with phyCARD-XL only. © PHYTEC Messtechnik GmbH 2011 L-758e_1... -
Page 26: Phywire-Eeprom
Display Adapter LCD-014-x / LCD-017-x phyWIRE-EEPROM This is for PHYTEC internal use only. © PHYTEC Messtechnik GmbH 2011 L-758e_1... -
Page 27: Technical Specifications
Technical Specifications Technical Specifications The physical dimensions of the LCD-014 (PL1337.1) and LCD-017 (PL1344.0) are represented in Figure 4 and Figure 5. Power consumption LCD-017: 10,4” LCD_5V = 536mA LCD_3V3 = 150mA LCD_3V3_S = 1mA 7” LCD_5V = 380mA LCD_3V3 = 150mA... -
Page 28: Figure 4: Lcd-014 Physical Dimensions
Display Adapter LCD-014-x / LCD-017-x 15mm Photosensor TP10 DISPLAY 050 V 32.5mm 185mm Figure 4: LCD-014 Physical Dimensions © PHYTEC Messtechnik GmbH 2011 L-758e_1... -
Page 29: Figure 5: Lcd-017 Physical Dimensions
152.5mm 117mm DISPLAY 104 S TP10 DISPLAY DISPLAY 070 W 035 V DISPLAY LCD_5V 050 V LCD_3V3 LCD_3V3_S LCD_3V3_S LCD_3V3 LCD_5V 12V_Backl. TP11 VLED Photosensor 6.5mm 178.5mm 263.5mm 268.5mm Figure 5: LCD-017 Physical Dimensions © PHYTEC Messtechnik GmbH 2011 L-758e_1... - Page 30 Display Adapter LCD-014-x / LCD-017-x © PHYTEC Messtechnik GmbH 2011 L-758e_1...
-
Page 31: Component Placement Diagram
Component Placement Diagram Component Placement Diagram R31 R32 C23 C22 TP10 Figure 6: LCD-014 Component Placement, Bottom View © PHYTEC Messtechnik GmbH 2011 L-758e_1... -
Page 32: Figure 7: Lcd-017 Component Placement, Bottom View
Display Adapter LCD-014-x / LCD-017-x Figure 7: LCD-017 Component Placement, Bottom View © PHYTEC Messtechnik GmbH 2011 L-758e_1... -
Page 33: The Display Adapters On The Phybase
The phyBASE Carrier Board provides a flexible development platform enabling quick and easy start-up and subsequent programming of the PHYTEC Extension Boards. The Carrier Board is compatible with all phyCARDs and its design allows easy connection of up to two extension boards as well as the display adapters. This supports a fast and convenient prototyping and software evaluation. -
Page 34: Controlling Touch With The Phybase
Display Adapter LCD-014-x / LCD-017-x Controlling Touch with the phyBASE Two touch screen controllers are available on the phyCARD Carrier Board. The choice which controller is chosen to handle the signals from the touch screen is pegged to the audio standard supported by the phyCARD. -
Page 35: Photo Sensor
In order to make 12V available for backlight, jumper JP2 must be closed. Caution: There is no protective circuitry for the 12V of the backlight! Close jumper JP2 only if the power supply connected to X28 of the phyBASE will not deliver more than 12V! © PHYTEC Messtechnik GmbH 2011 L-758e_1... - Page 36 Display Adapter LCD-014-x / LCD-017-x © PHYTEC Messtechnik GmbH 2011 L-758e_1...
-
Page 37: Mounting A Display Adapter On A Baseboard
Fastening the integral hinge to the baseboard will be done the same way. Therefore PHYTEC ships the display adapter together with a separate aluminum slat and the baseboard comes with the needed screws. -
Page 38: Screwing
Display Adapter LCD-014-x / LCD-017-x Figure 9: Screwing • Put one screw through the wide opening of one plastic spacer bolt and screw it through the first hole of baseboard and integral hinge into the aluminum slat. • Do the same with a second screw and the second hole. -
Page 39: Figure 11: The Result
Mounting to the phyBASE Figure 11: The result... Ready! Fold the two boards together and put the kit on its “feet”. © PHYTEC Messtechnik GmbH 2011 L-758e_1... - Page 40 Display Adapter LCD-014-x / LCD-017-x © PHYTEC Messtechnik GmbH 2011 L-758e_1...
-
Page 41: Revision History
Revision History Revision History Date Version Changes in this manual numbers July 2011 Manual First edition L-758e_1 © PHYTEC Messtechnik GmbH 2011 L-758e_1... - Page 42 Display Adapter LCD-014-x / LCD-017-x © PHYTEC Messtechnik GmbH 2011 L-758e_1...
- Page 43 Suggestions for Improvement Document: Display Adapter LCD-014 / LCD-017 Document number: L-758e_1, June 2011 How would you improve this manual? page Did you find any mistakes in this manual? Submitted by: Customer number: Name: Company: Address: Return to: PHYTEC Technologie Holding AG...
- Page 44 Published by © PHYTEC Meßtechnik GmbH 2011 Ordering No. L-758e_1 Printed in Germany...
Need help?
Do you have a question about the LCD-014 and is the answer not in the manual?
Questions and answers