Advertisement
'-.~
REAR
WIN"DOW
lllATCH
RELeASE
INSTALLATION
~STRUCT'ONS
PARTS E"CLOSED:
Qty.
1
Solenoid
2
Machine Screw
2
Washers (Solenoid)
1
E-Clip
1
Washer (Cable)
1
Wire Harness (Red)
1
Wire Harness (Blk.)
1
Tap Connector
1
Snap Ring
Switch Button
SwItch Bracket
Bracket Screw
Cable Tie
InstructIon Sheet
Part
EMD20-987
EMA15-217
EMA7e.242.
EM178-123
EMA78-243
EMB210-107
EM62'0-10e
EMA226-123
EMAS5.'48
EMA26-104
EMC29-309
EMA15-214
EMA22-102
EMA40-102
STEP 5. Inst811 Switch Button.
A. Glov.
box lnetallatlon.
If you are installIng your switch In the glo'ie bOx many models
have plugged holeS alreedy in them. If your vehicle is 90
equipped. remo'ie the plug. The hole may be either 3/4. or' II in
diameter
If the hole is' .diameter
you will need to use the
optional snap ri(\Q. Glove boxes without plugged holes will
require a 3/4" diameter hole be cut (Caution: Remove glove
box insert before drilling Hole). Once your hole is located. route
the connector plugs on tt1e black and red wires through and
connect them to t~e switch button. Push the switch button into
the hole.
8. Under dash Inata'lltlon.
If you are installing the switch button under the dash you will
need to use the switch bracket and snap ring. Remove a screw
under the dash or use tn9 enclosed self-tapping ICfew and
inatall the switch button bracket. Connect the wiring to the
switch button 8S d8scribed in abo"e paragraph.
1
1
1
1
, STEP 6. Connecting
the Swttch Button.
Taking the blank end of the red wire determine If you wish to
connect at the fuse box or splice into an exist\ng w\~
DecIde
lWhether you want your power source to be ignition activated or
lconstant and complete tM connection. Your switch will be
'operable uoon reconn~ing
the battery.
STeP ,. Dlaconnect PO8ittv. Battery Cabl.
STEP 2. ; Refnov. Panel From R..r Uftgat.
STEP 3. 1n8t8l1 SolenoId
Figure At below shows the so\enoid instaltation k>oklng through
the ext~r
sheet metal. Once you have the inside panel
-,.mcw84
from ~te
you wtR MKt have to rernove th8- .
metal cover over the latch mechanism and tn. metal bracket
occupyt~ the tailgate lICCeta hole. Orientate the solenoid
inside the liftgate acc988 aligning me solenoid bracket holes
with the i holes in the liftgate. Using the two maChine screws
with w88hers attach the solenoid to in. liftgat. by inserting the
~ehers
through the sheet meial and into the solenoid
bracket ;until fIght. Next attach the solenoId cable to the latch
lever -shown
in fIgure B.
STEP 7. T..t
.AdJUat
Close rear hatcn and push switch button. If window opens,
move to Step 8. if it does not open and your system is ignition
activated, insure the key is on. It solenoid ~1ick8 but window
does not open check assembly to latch for proper connection. It
solenoid does not click check your power source connection.
STEP 8. Flnleh
Remove or loosen neces8ary trim along the wiring route to the
solenoid. Tuck the wiring beneath the trim P8"8I8 and tighten.
Replace rear trim panel on liftgate. Vour in8'allatlon is
complete.
STEP 4. AouUng WIN H.neaa
Plug one end of black wire into aoleno\d oon~or
and route
w'n along 8id8 tr1m pan...
to the location where you wish to
in..I'
~f
9w\tch button. Leave wire loose until step 8.
Advertisement
