Princeton Tec ALLOY-X SPOT HIGH Operating And Maintenance Instructions

ALLOY-X
DUAL FUEL
LED PEN LIGHT
Operating and Maintenance Instructions
ENGLISH:
LED Charging Indicators
The LED on the positive end of the battery housing lights up
when the cable is correctly installed.
• Charging - Red LED is illuminated.
• Fully Charged - Green LED is illuminated.
Charge time is approximately 4.5 hours.
IMPORTANT: Maximum charging temperature range is 20°F
to 115°F with optimal temperature range between 50°F
and 86°F. A safety circuit prevents charging outside the
maximum range and the red charge LED will pulse rapidly.
When temperature is within an acceptable range charging
will resume.
Battery Installation
– See Battery Installation Diagram
Alloy-X uses one 10900 Lithium Rechargeable Battery, as
supplied by Princeton Tec. It is also compatible with 2 AAA
Alkaline batteries.
When not using Alloy-X, separate the head and tail by
turning counterclockwise approximately one turn. This
will prevent accidental activation. Remove batteries when
storing Alloy-X.
Observe proper battery polarity when installing the batteries.
Improper installation of the batteries will damage light and
void warranty.
WARNING !
• Never mix fresh and used batteries.
• Never mix different battery brands or chemistry types.
• Always remove drained batteries i`mmediately.
• Remove batteries during long periods of storage.
Switch Operation
– See Figure 2
ON/OFF
With the light off, a full press of the tail switch will produce
an audible "click" and the light will turn on. The default is
MEDIUM output. Another full press will turn the light off.
Brightness Adjustment
From ON, a half press of the tail switch will cycle through the
three output modes. Default is to turn on in MEDIUM. The
next half press will produce LOW which is then followed by
HIGH and then a return to MEDIUM. The cycle will repeat.
From OFF, a full press will turn the light on the next mode
in the cycle. For example, if the light is on in MEDIUM and
then turned off, the next full press from OFF will turn the
light on in LOW. If the light is turned off, the next click will
result in HIGH. The cycle will repeat.
Note: If the light is left off more than one minute it will reset
to the default which is turning on in MEDIUM.
Figure 1 – Battery Replacement
1
Figure 2 – Switch Operation
®
Figure 3 – Performance
Note: performance is based on Princeton Tec rechargeable battery. AAA output will be somewhat lower.
Modes
SPOT HIGH
SPOT MED
SPOT LOW
DISTANCE (m)
(ANSI FL-1 Standard)
Runtime is defined as the duration of time from the initial light output value—defined as 30 seconds after the
point the device is first turned on—using fresh batteries, until the light output reaches 10% of the initial value.
Figure 2 – Charging
1
General Maintenance
• Do not disassemble the sealed head as doing so may
cause damage to the flashlight and void the warranty.
• Replace the O-rings if they become stretched or damaged.
Regularaly lubricate the O-rings.
• Clean the contacts of your light periodically
•
Troubleshooting
If the Alloy-X fails to light:
• Check the battery to see if it needs to be recharged
• Check the batteries for proper installation.
• Replace batteries if proper installation is confirmed.
• Check the PCB board contacts or battery contact for dirt
• Clean the contct points with an alcohol soaked cotton swab.
USA– International 5-Year Warranty
WARRANTY – Princeton Tec warrants this product to be free
from defects in workmanship and materials under normal
use for 5 years. This warranty covers all of the component
parts of the product except batteries. This warranty does not
cover deterioration due to normal wear or damage due to
misuse, alteration, negligence, accidents, or unauthorized
repair. Princeton Tec will repair or replace parts which are
defective in workmanship or materials.
Your authorized Princeton Tec Dealer and Princeton Tec are
the only facilities authorized to repair the product. After (3)
unsuccessful attempts (within the warranty period) to repair
the product, you have the right to elect replacement of the
product or a refund of the purchase price less allowance
for use of the product. NO INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARE INCLUDED IN THIS WARRANTY. (Some
states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitations or
2
Standard operation:
Press 1x:
On / Medium
From Medium
Quickly press 2x (off and on) :
Low
From Low
Quickly press 2x (off and on) :
High
Press 1x from On:
Off
Lumens Runtime Beam Pattern
400 0.5h
250 1.25h
5 28h
0
2
3
Rechargeable Battery
+ -
2 AAA Alkaline
+ - + -
Alternate operation
From Medium
Half press 1x (no click) :
Low
From Low
Half press 2x: (no click) :
High
From Medium
Half press 3x: (no click) :
High
From Off:
Cycle-memory continues for
one minute, then resets
6 50
3
CHARGING
exclusions may not apply to you.) This warranty gives you
specific legal rights, and you may also have other rights
which vary from state to state.
Princeton Tec reserves the right to change product
specifications without notice.
FOR CALIFORNIA RESIDENTS:
WARNING: This product contains Bisphenol A (BpA) a
chemical known to the State of California to cause birth
defects or other reproductive harm.
Return Policy
If your light fails to operate, follow these simple steps:
1. Check batteries. Replace if necessary.
2. To send your light in for repair or replacement, first
contact Princeton Tec customer service on
1-800-257-9080 to request an RMA number. Please
have your light model, date of purchase and a brief
description of the fault you are experiencing. No
warranty repairs will be accepted without an RMA
number.
3. Return the light without batteries to: Princeton Tec, PO
Box 8057 Trenton NJ 08650. Postage due and freight
collect items will not be accepted.
4. Upon receipt your light will be processed in about
two weeks. Please allow additional time for return
transportation from NJ.
Princeton Tec
PO Box 8057,
Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
princetontec.com
© 2021 Princeton Tec
72
FULLY
CHARGED