Table of Contents
Advertisement
Quick Links
Berner- Kochsysteme GmbH & Co. KG
Sudetenstrasse 5 - D-87471 Durach
Tel. +49 (0) 831/697247-0; fax. - 15
enamel:
operating instructions
Installation-Induction fryingplates
*Options: GSG1, GSG2, ESB, EOI, ESRTI
Be sure to
read
before installation - installation - commissioning.
This protects you and prevents damage.
Berner@induktion.de
from - Y.O.M. 2014
BGI40, BGI60, BGI80
the instructions for use and assembly
|
www.induktion.de
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Berner BGI40
Summary of Contents for Berner BGI40
- Page 1 Berner- Kochsysteme GmbH & Co. KG Sudetenstrasse 5 - D-87471 Durach Tel. +49 (0) 831/697247-0; fax. - 15 enamel: Berner@induktion.de www.induktion.de operating instructions Installation-Induction fryingplates from - Y.O.M. 2014 BGI40, BGI60, BGI80 *Options: GSG1, GSG2, ESB, EOI, ESRTI Be sure to...
-
Page 2: Table Of Contents
Heating states (function key active) ..................12 Residual heat indicator ......................12 service ........................... 13 Cooking process ........................13 comfort ..........................13 Software Version ........................13 Meaning Decimal Point: ...................... 13 side 1 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... - Page 3 Additional installation requirements for the installation model ......... 29 Attention points for remote coil (coil - generator separated) ..........29 Installation instructions for the installation of Berner ..............30 Sensor keypads with support frame (Ver. A) ................30 Installation instructions for flush-mounted installation ..............31 (Ver.
-
Page 4: Safety
Aluminum foil and plastic vessels melt on hot stoves. The heatof stove protection film on the heating zone(n) is not recommended. Never cool or clean with cold water or ice cubes. This leads to damage. side 3 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 5: Safety Regulations
Danger to persons due to overheated storage area Safe use The safety provisions of this manual, the existing national rules on electricity to prevent accidents and any internal working, application andsafetyregulations must be followed. side 4 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 6: Improper Operation
When disassembly, testing or repairs, pay attention to the stability of the device. Attention! When replacing spare parts, the induction device must be "visibly tt" from the power supply. side 5 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 7: Monitoring Of The Heating Zone
Frequency50 / 60 Hz Protection class in delivery state with module IP 21 Protection class in delivery state with separate generator (GSG1/2) IP 11 side 6 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 8: Power Tabe 1 Channel (Single Generator Bips)
Tax security frequency 22-35 Yellow/Green Installation environment Maximum ambient temperature Storage >-20°C to +70°Cin Function>+5°C to +35°C maximum relative humidity Storage> 10% to 90% in function> 30% to 90% side 7 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 9: Installation Pre-Conditions
For the electrical connection of the device, the legal Regulations of the respective country! attention attention Incorrect voltage can cause the The electrical connections must be carried Damage induction device out by a specialist. side 8 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 10: Commissioning
If the heating zone is split or broken, immediately turn off the device and disconnect the power plug. Turn the main switch to the OFF position (0) before Connect inductiongerät to the power grid. side 9 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 11: Devices On And Off Switch
Heats: point to the right of symbol SHOULD temperature 70°C (point), actual temperature within +/- heat 2°C, Does not IS temperature 105°C, actual temperature too high, does not heat side 10 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 12: Control With Touch Control Panel
(Is temperature equal to target temperature +/- 2C°). The device keeps thetemperature. Heating state "u" The set set temperature is lower than the IS temperature (too hot). Heating OFF side 11 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 13: Function Key
The device is switched off but still hot (above 45C°) then the residual heat display, which is represented by " - ". attention Injuries and burns to avoid touching the heating zone. side 12 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 14: Service
1 sec. pulse = limitation due to too high heat sink temperature 1/2 sec. pulse = limitation due to excessively high coils/pan temperature 1/4 sec pulse = power limit 1/10 sec. pulse = power limitation with not optimal Material side 13 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 15: Decommissioning
The inductiongerät must be switched off immediately and the power plug pulled out. Do not touch any parts inside the device. attention Do not open the induction device! Dangerous tension! side 14 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 16: Troubleshooting
If the mains connection line of this device is damaged, it must be replaced by the manufacturer or its customer service or a similarly qualified person to avoid hazards. side 15 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 17: Overview Error Messages On Display
Warning: Fan not connected or blocked (after start 5 sec, then every 10 sec for 1 sec.) Overcurrent on induction coil, then 10 sec. pause. Device Off and Back On Switch On side 16 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 18: Cleaning
15-20 min, if the frying plate still has residual heat, clean the plate only with water and the stainless steel sponge using the frying filler and then oil again. side 17 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... - Page 19 18 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014...
-
Page 20: Warranty
Devices intended for this purpose can be sent to us for disposal. Only enough prepaid packages are accepted by us. Delivery: Berner- Kochsysteme GmbH & Co. KG Sudetenstrasse 5 - D - 87471 Durach Tel. +49 (0) 831/697247-0; fax. - 15 enamel: Berner@induktion.de... -
Page 21: Declaration
Declaration EC Declaration of Conformity Declaration of conformity Berner- Kochsysteme GmbH & Co. KG Sudetenstrasse 5 - D-87471 Durach We hereby declare that the device referred to below complies with the relevant, basic safety and health requirements of the EC Directive due to its design and design, as well as the design we place on the market. - Page 22 21 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014...
-
Page 23: List Of Spare Parts
. .. • - . .. " • • . . • • . . • • . . • • • • • • - - - side 22 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... - Page 24 • - - - •• ••• • • • • - • • • , , , •• • • • •• • • " " side 23 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014...
-
Page 25: Bipds Generators
•• • - - - - - - - • .. ••• - - - - - - - - - - •. .. •. .. •. .. side 24 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... - Page 26 - - - - • " " • • • • , , , •• • .. • • •• , , , • .. • • .. • side 25 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014...
-
Page 27: Technical Documentation
Technical documentation Device view (example: BGI40) Installation example Setting up the device Stainless steel cover Edge approx. 10-12 mm Fuse for ventilation Safety thermostat Item: 501260 side 26 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 28: Airflow
Air flow module Air way coil generator Separate (Standing/ Lying) side 27 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 29: Observe Installation Regulations
(near fritteusen, grill plates or frying tippers). The air intake temperature must be below +35°C. Operators must ensure that all installation, maintenance and inspection work is carried out by approved personnel. side 28 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 30: Additional Installation Requirements For The Installation Model
EMC test, electrical safety. The execution of the inspections is the responsibility of the user and should be confirmed by an accredited inspection body. side 29 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014... -
Page 31: Installation Instructions For The Installation Of Berner
Installation instructions for the installation of Berner Sensor keypads with support frame (Ver. A) Frame incl. electronics is vorassembled with glued ceramic glass Please note the following installation instructions. This is the only way to ensure trouble-free operation and a long service life. In the event of a breach of these requirements, the device warranty expires. -
Page 32: Installation Instructions For Flush-Mounted Installation
Installation instructions for flush-mounted installation (Ver. A2) by Berner Sensor keypads Frame incl. electronics is pre-assembled with glued ceramic glass Please note the following installation instructions. This is the only way to ensure trouble-free operation and a long service life. In the event of a breach of these requirements, the device warranty expires. -
Page 33: Installation Instructions For Flush-Mounted Installation
Installation instructions for flush-mounted installation (Ver. B) by Berner Sensor keypads Frame incl. electronics is pre-assembled with glued ceramic glass (2 - 3mm projection) Please follow the instructions on page 37 Please note the following installation instructions. This is the only way to ensure trouble-free operation and a long service life. -
Page 34: Installation Instructions For Flush-Mounted Installation
Please note the following installation instructions. This is the only way to ensure trouble-free operation and a long service life. In the event of a breach of these requirements, the device warranty expires. side 33 from 34 08.11.2014 Ver. 2.9 © Berner cooking systems 2014...
Need help?
Do you have a question about the BGI40 and is the answer not in the manual?
Questions and answers