Table of Contents
Advertisement
Quick Links
SIGNALTESTER RJ-F
wire tester
The Signaltester RJ-F wire tester analyzes wiring on phone, computer network and
coax cables in one easy step. The large backlit LCD display maps out connections
and describes wiring faults.
The built-in tone generator and the included Video and Data remote identifiers
can be used to quickly locate cables in waring closets and patch panels.
WARNINGS
Do not connect the Signaltester RJ-F to a live circuit. Exposure to voltage can
damage the tester.
Do not modify or try to repair the tester. No serviceable parts are inside.
Do not use the tester in a wet or damp environment or during electrical storms.
Visually inspect an RJ plug before inserting it into the tester. Poorly terminated
plugs may damage the jacks on the tester.
Plugging an RJ11 of RJ12 connector into the RJ45 jack of the Signaltester RJ-F
may damage the RJ45 jack.
Please read the complete safety instructions in the booklet delivered with this
device.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Futech SIGNALTESTER RJ-F
- Page 1 WARNINGS Do not connect the Signaltester RJ-F to a live circuit. Exposure to voltage can damage the tester. Do not modify or try to repair the tester. No serviceable parts are inside.
-
Page 2: Lcd Display
DESCRIPTION TESTER Video - F-connector Voice - RJ11/RJ12 Jack Data - RJ45 Jack LCD Display Data button Voice button Cycle button Video botton Tone button 10. On/Off button REMOTE & ID’S 11. Voice - RJ11/RJ12 Jack 12. Data - RJ45 jack 13. -
Page 3: Operation
The cables will interact with each other and alter test results. Press ON/OFF button to turn on the Signaltester RJ-F. Press the Voice button to select the voice wire test function. Connect one end of the cable under test to the RJ11/RJ12 port on the tester. - Page 4 1-6 ndicate an open pair. DATA Warning: Exposure to voltage can damage the Signaltester RJ-F. Immediately dis- connect the cable under test is Voltage warning appears on the display. Make sure the vable is not connected to any device that can supply voltage before retesting.
- Page 5 It is necessary to use the Signalprobe RJ-F. Signalprobe RJ-F Connect the cable under test to the RJ45 port on the tester. Press the ON/OFF button to turn on the Signaltester RJ-F, than press the Data TEST MODE button to select the data wire test function.
- Page 6 miSS-wired. Wiring and Display Examples for Data Cable · T568B Data Cable Properly Wired Pass appears on the display indicating a properly wired cable. The pin numbers on the top row agree with the bottom row indicating proper continuity. Both the T568A and T568B wiring standards will test the same as long as the same standard is used on both ends of the cable ·...
- Page 7 Connect a numbered COAX-remote to the wall port at the other end of the cable under test. Press the ON/OFF button to turn on the Signaltester RJ-F and press the Vid- eo button to select the video cable test function Interpret the results using the Wiring and Display examples for Video further in this manual.
-
Page 8: Battery Replacement
Connect the numbered remote IDs to the F-connector port for each location needs to be identified. At the patch panel, connect the unknown cable to the F-port on the Signaltester RJ-F. Press the ON/OFF button to turn on the tester and press Video to select the video cable test fucntion. -
Page 9: Specifications
100Ω max. DC Dimensions 152x61x34 Weight 230g Futech is a registered brand of Laseto NV, Belgium. Futech declares that the Signaltester RJ-F is in conformity with the following standards: · EN 61326-1:2013 · EN 61326-2-2:2013 following the provisions of Directive: ·...
Need help?
Do you have a question about the SIGNALTESTER RJ-F and is the answer not in the manual?
Questions and answers