Download Print this page

Advertisement

Quick Links

BSL STIMULATORS
Modular Stimulators (0-100 V):
BSLSTMB for MP36/36R/35
BSLSTMA for MP30/35/36/36R
See also: HSTM01, ELSTM1, ELSTM2, EL300S and EL400 electrodes.
BSLSTMB
The older "BSLSTM" uses dial reading and a flip range switch. The same guidelines and
Note
cautions described here apply, except when noted.
The BSLSTM Stimulator works in conjunction with the Biopac Student Lab System to allow precise stimulus
pulse outputting. Use the BSLSTM and the BSL PRO to perform a wide array of measurements, such as:
Twitch sub-threshold & threshold
Maximum twitch responses
Single twitch, summation
STIMULATOR PULSE DEFINITIONS
Pulse width
Delay before first pulse
Repetition period
Pulse rate
PRODUCT SHEET
Low Voltage Stimulator/Adapter:
OUT3 Output Adapter for built-in Stimulator (MP36 only)
SS58L Low Voltage Stimulator (MP35 only)
BSLSTMA
Muscle tension/length vs. force
Tetanic contraction
Nerve conduction
The time that the pulse is in the non-zero or active state.
The initial delay from the start of acquisition to the start of the first pulse.
The time between pulses, as measured from the start of one pulse to the start
of the next pulse. This is the inverse of the Pulse rate.
The number of pulses that occur in a one-second interval, expressed in Hz.
The Pulse rate relates to the Pulse period as follows:
BIOPAC Hardware |
STIMULATORS MP3X
info@biopac.com
support@biopac.com
www.biopac.com
Lab set up note
Placing the BSLSTMA/B unit too close to
MP3X hardware can result in data distortion
of the BSLSTMA/B pulse width signal; the
distortion is more apparent at higher sampling
rates.
NEVER set the BSLSTMA/B atop an
MP3X
Position the BSLSTMA/B away from the
MP3X to reduce the signal distortion
Fatigue
Velocity
| Page 1 - 9
Updated: 9.12.2019

Advertisement

loading
Need help?

Need help?

Do you have a question about the BSLSTMB and is the answer not in the manual?

Questions and answers

Summary of Contents for BIOPAC Systems BSLSTMB

  • Page 1 BSL STIMULATORS Modular Stimulators (0-100 V): Low Voltage Stimulator/Adapter: BSLSTMB for MP36/36R/35 OUT3 Output Adapter for built-in Stimulator (MP36 only) BSLSTMA for MP30/35/36/36R SS58L Low Voltage Stimulator (MP35 only) See also: HSTM01, ELSTM1, ELSTM2, EL300S and EL400 electrodes.
  • Page 2: Front Panel Terminology

    info@biopac.com PRODUCT SHEET support@biopac.com www.biopac.com Also called — Pulse rate (Hz) = 1000 / Repetition period (milliseconds) Pulse frequency Repetition rate Events per second Use when referring to either Pulse rate or Pulse period. Pulse Repetition The amplitude of the pulse, expressed in Volts. Pulse level The output of the BSLSTM is 0 Volts when the pulse is not active.
  • Page 3 info@biopac.com PRODUCT SHEET support@biopac.com www.biopac.com As shown in the following diagram, the indicator mark is between the two dials. Close-up of “Level” adjustment knob Stimulus pulse output for connection to external electrodes or other devices. This is a Stimulus output standard BNC style connector.
  • Page 4 info@biopac.com PRODUCT SHEET support@biopac.com www.biopac.com Calibration The “Reference Output” signal from the BSLSTM must be calibrated to ensure accurate results. 1. Choose the correct Preset (via MP3X menu > Set Up Data Acquisition > Channels). ▪ For example, if using the BSLSTMA/B, (this Preset found in older BSL 3.7.x software only) don’t choose a “BSLSTM...”...
  • Page 5 info@biopac.com PRODUCT SHEET support@biopac.com www.biopac.com CONNECTING THE BSLSTM TO THE MP3X 1) Turn the MP3X unit OFF. 2) Confirm that Power switch on the back of the BSLSTM is in the OFF position. 3) Set the Range on the front of the BSLSTM to 0-10 V. 4) Set the Level to 1 Volt.
  • Page 6 info@biopac.com PRODUCT SHEET support@biopac.com www.biopac.com (This new unit has digital display and a keyed range switch) BSLSTMA/B SPECIFICATIONS Pulse width Controlled by: Computer, with lockable width limit 0.49 – 100 milliseconds Range: Resolution: 2 microseconds 5% (Can be improved to better than 2% using the “Correction factor” in the Accuracy: “Stimulator Preferences’...
  • Page 7 info@biopac.com PRODUCT SHEET support@biopac.com www.biopac.com (This older unit uses dial reading and a flip range switch) BSLSTM SPECIFICATIONS Pulse width Controlled by: Computer, with lockable width limit 50 microseconds – 100 milliseconds Range: Resolution: 2 microseconds 5% (Can be improved to better than 2% using the “Correction factor” in the Accuracy: “Stimulator Preferences’...
  • Page 8 info@biopac.com PRODUCT SHEET support@biopac.com www.biopac.com LOW VOLTAGE STIMULATOR OUT3 The MP36 includes a built-in low voltage stimulator—just use the Analog Out port. • For connection to BIOPAC electrodes, add the OUT3 BNC Adapter. SS58L The MP35 uses the SS58L Low Voltage Stimulator to the Analog Out port. Connect any electrode or lead with a BNC connector (such as needle electrodes or clip leads) for direct stimulation of animal or tissue preps.
  • Page 9: Please Read

    info@biopac.com PRODUCT SHEET support@biopac.com www.biopac.com TIMULATOR ELECTRODE UIDELINES — — PLEASE READ It is very important to follow the electrode placement guidelines when connecting stimulator electrodes from the BSLSTM to a subject. The BSLSTM can output lethal levels of energy! ❖...

This manual is also suitable for:

BslstmaOut3Ss58l