Subscribe to Our Youtube Channel
Summary of Contents for Markes International C-HLD
- Page 1 QUI-1166 Version 1 August 2019 Helium leak detector Instruction for use roduct eference Helium Leak Detector, with USB charger C-HLD www.markes.com...
-
Page 2: Table Of Contents
QUI-1166 Contents 1. Introduction .............3 Important safety warnings ........3 Warnings ..............3 Operational notices ..........4 2. Components .............5 3. Preparation ..............6 4. Detector operation ..........6 5. Storage ..............8 6. Setting parameters ..........9 Parameter setting items and contents ....9 Flow diagram of parameter settings .......10 7. Specifications ............11 8. -
Page 3: Introduction
QUI-1166 Introduction This portable, highly sensitive helium leak detector for TD–GC systems provides the accurate, sensitive and rapid detection of carrier gas leaks that is essential for TD–GC troubleshooting. Through a dual system consisting of an LCD display and an audible alarm, this qualitative device clearly indicates gas leaks, and is powered by rechargeable batteries for ease of portability. -
Page 4: Operational Notices
QUI-1166 Operational notices DO NOT use the detector to detect corrosive gases. WARNING DO NOT use the detector in environments that are contaminated with WARNING dust or combustible fumes. DO NOT use the detector outside of the specified temperature range WARNING (10 to 40°C) DO NOT expose the detector to shock. WARNING Ensure the device is in a stable condition during operation. -
Page 5: Components
QUI-1166 Components FUNC/POWER key Turning the power ON/OFF and selecting setting contents. ZERO/ENTER key Adjusting zero balance and entering setting contents. LCD display LED indicators Indicating leak level and battery level Reference Port Inlet to aspirate ambient air Charging terminal Connecting the charging terminal to a PC with supplied micro USB charging cable to charge Battery Cover... -
Page 6: Preparation
QUI-1166 Preparation Prior to first use, or before using the product following an extended period of disuse, ensure the device battery is fully charged. DO NOT turn on the power of the detector while the battery is being WARNING recharged. After recharging, allow the detector 30 minutes to stabilize its temperature before use. The charging terminal cap should be attached, except for when charging. - Page 7 QUI-1166 After warm-up, the standard display is shown. ➊ ➌ ➋ Standard display (Similar displayed at Range Hi.) (Range Std.) ➍ Range ➊ R_Std: Standard Sensitivity Range R_Hi: High Sensitivity Range (10 times more sensitive than standard range) Battery indicator ➋ Battery indicator shows the battery charge levels in 3 levels: Battery level 3: Full charge (more than 50% is left) Battery level 2: Low charge (about 20–30% left)
-
Page 8: Storage
QUI-1166 First, check the stability at zero point. & on the left will be blinking alternately when the detector becomes stable. When the leak indicator is displayed without leakage, press ZERO/ ENTER key to adjust the zero balance. Under conditions such as fluctuation of temperature or humidity, the detector needs zero point adjustment for both the LED and LCD display. Out of zero point ZERO adjust Place the sample probe tip near the gas connection to leak check. -
Page 9: Setting Parameters
QUI-1166 Setting parameters Parameter setting items and contents Parameter setting item Content Sets range Range Std: Standard sensitivity range Hi: High sensitivity range Sets the buzzer to alarm Buzzer ON: Use (More than 3 gas leak marks) OFF: Not use Sets LED in combination with LCD display ON: Use OFF: Not use... -
Page 10: Flow Diagram Of Parameter Settings
QUI-1166 Flow diagram of parameter settings : At blinking (Selecting) condition Page 10 www.markes.com... -
Page 11: Specifications
Display ■ Leakage display: LCD or LED ■ Parameter setting display: LCD Contact details For technical support, please contact your supplier in the first instance. If they are unable to resolve your query, please contact Markes International’s service department: E: support@markes.com T: +44 (0)1443 230935 W: www.markes.com www.markes.com Page 11... - Page 12 QUI-1166 L-0150 (160819-1)
Need help?
Do you have a question about the C-HLD and is the answer not in the manual?
Questions and answers