Summary of Contents for Wireless Solution W-DMX G6 BLACKBOX F-1
Page 1
W-DMX USER MANUAL ™ B L A C K B O X F - 1 B L A C K B O X F - 2 B L A C K B O X R - 5 1 2 L a t e s t re v i s i o n : D e c e m b e r 2 0 2 0 w w w.
User Manual TABLE OF CONTENTS 1. SAFETY INFORMATION ........................4 1.1. E ............................4 NGLISH 1.2. D ............................5 EUTSCH 2. YOUR WIRELESS DMX G6 SYSTEM ....................6 4. USER INTERFACE ..........................8 4.1. F-1 R-512 ........................8 MODELS 4.2. F-2 ............................
User Manual 1. Safety information WARNING / WARNUNG / ATTENTION / ADVERTENCIA / VARNING / ADVARSEL / VAROITUS / ADVARSEL This product must be earthed. Das Gerät muss an eine geerdete Steckdose angeschlossen werden. Cet appareil doit être branché à une prise de terre. Este aparato se debe conectar a una toma de tierra.
User Manual 1.2. Deutsch 1. Bitte lesen Sie diese Hinweise und Sicherheitshinweise sorgfältig durch, bevor Sie dieses Produkt verwenden. 2. Bewahren Sie diese Anleitung zum späteren Nachschlagen auf. 3. Das Produkt nie anschließen, wenn es sich in der Verpackung befindet- Außerdem darf das Produkt beim betrieb nicht abgedeckt werden.
W-DMX™ Configurator App. You may find W-DMX™ being used by several lighting manufacturers – this protocol, if specifically named “W-DMX™” will work in an identical way as a branded Wireless Solution product, and it is therefore compatible with our transmitters and receivers.
Page 7
User Manual 3. The W-DMX Technology ™ W-DMX is engineered by Wireless Solution Sweden to provide the same quality, reliability and ™ performance as any wired DMX link. The technology allows you to establish point-to-point links, point-to-multipoint and multipoint-to-multipoint: W-DMX ™...
User Manual 4. User Interface Though the interface display appears simple, there is a lot of information you can read back, which will help you properly set up your system and help you understand how your devices are operating. 4.1. F-1 and R-512 models 1.
User Manual 4.2. F-2 model 1. Red function button Radio A 2. TX Device is operating as a transmitter. 3. LINK On a transmitter; states it’s ready to establish a link. On a receiver; • Off: not linked to any transmitter •...
User Manual 5. Hardware 5.1. F-1 and R-512 models 1. AC Power Supply connector, powerCON® TRUE1® 90-250V / 50-440 Hz (for other voltage and frequency options, contact manufacturer) 2. WiFi antenna NOTE: Option to be purchased separately – contact manufacturer. Not available on R-512 model. 3.
User Manual 5.2. F-2 model 1. AC Power Supply connector, powerCON® TRUE1® 90-250V / 50-440 Hz (for other voltage and frequency options, contact manufacturer) 2. WiFi antenna NOTE: Option to be purchased separately – contact manufacturer. Not available on R-512 model. 3.
User Manual 6. Operation All W-DMX™ G6 devices uses similar user interfaces, however some model-specific differences may apply. 6.1. Basic setup – Linking devices A basic setup is defined by the link between two devices. This means that, in order to send data from a transmitter to a receiver, it’s necessary to link the devices: Press the red function button, on the transmitter momentarily and the LINK LED starts flashing.
User Manual 6.3. Linking multiple transmitters with multiple receivers When multiple receivers need to be linked up with different transmitters, repeat the process in 6.1., but turn off all receivers you do not wish to pair up. For example: If you have 2 transmitters and 10 receivers, pair the first transmitter to 5 receivers, while the last five are turned off.
User Manual While operating as a TX you can change between modes at any given moment: 1. Press the red function button rapidly 3 times. 2. Press and hold the red function button for at least 3 seconds. 3. Each time you press the red function button you will step through the available modes; this will be indicated by the MODE LED.
User Manual 6.7. RDM As default, all products come with RDM disabled. To use RDM, this must be enabled from within the W-DMX Configurator app. The changes must be done on the transmitter and on each receiver that needs to do downstream RDM.
Configurator app. 7.3. Firmware Update Wireless Solution is committed to developing and improving its wireless technology – this means that we every now and then releases new firmware versions. Sometimes it might be added functionality, but since even the best makes mistakes sometimes – we might release bug fixes also.
User Manual 8. Tips & tricks There are several tips and tricks that could make your wireless transmission work better. Here’s a few that should be followed: It’s important that all antennas point to the same axis – wireless waves have a radial pattern that should be valued.
FCC Declaration of Conformity We Wireless Solution Sweden AB, Majorebergsgatan 2, 451 75 Uddevalla, Sweden, declare under our sole responsibility that this product complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: •...
Products to be returned under warranty must be accompanied by an RMA Authorization Number. Wireless Solution AB does not warrant that the operation of the product will be uninterrupted or error-free. The manufacturer is not responsible for damage arising from failure to follow instructions...
Page 20
h e l p d e s k @ w i re l e s s d m x . c o m W i re l e s s S o l u t i o n S w e d e n A B M a j o re b e rg s v ä...